General Electric Screws, Nuts, Washers

Includes 12 washers.

This pulley nut secures the washing machine's drive pulley to its shaft, helping keep the belt aligned so the basket can agitate and spin smoothly. Replacing a worn or missing nut helps prevent pulley wobble and belt issues. What it does:

• Fastens the drive pulley securely to the shaft
• Helps maintain proper belt tracking and drive engagement
• A loose, stripped, or missing nut may cause rattling or scraping noises, belt slippage or the belt coming off, and intermittent or no spin/agitation

• One pulley nut

• Disconnect power and water; wear appropriate PPE
• Access the drive pulley from the rear or bottom per the service instructions
• Support the pulley while loosening/tightening the nut to avoid stressing the shaft
• Pulley seating and belt alignment before reassembly and test run

This OEM fastener secures interior components and trim on compatible appliances to restore proper fit and reduce movement. It's a direct-replacement hardware piece used where the original mounting screw or retainer is lost or worn. What it does

• Secures panels, trim pieces, brackets or small assemblies to the appliance frame
• Restores firm attachment to reduce rattles, gaps or misalignment
• Replaces missing or stripped hardware that prevents proper part installation
• Helps maintain proper operation by keeping service parts seated and stable

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start the fastener, then tighten snugly—do not over-torque
• Replace any additional damaged fasteners with the same OEM part for best fit

This ST4 x 20 screw replaces a lost or damaged fastener and secures panels or brackets in your washer, restoring a tight fit and helping eliminate vibration and rattling caused by loose hardware.

• Fastens panels, brackets, or covers to the washer cabinet
• Replaces missing, stripped, or corroded screw specified as ST4 x 20
• Helps keep components aligned to reduce vibration and noise
• Useful during reassembly when the original screw won't hold

• Disconnect power before servicing; turn off the water supply.
• Match the screw length and thread to the original location; do not mix different screws.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Transfer any original spacers or washers used with this screw.

This handle tapping screw secures an appliance's handle to its door or front panel. Replacing a missing or stripped screw restores a firm, safe grip and prevents a loose or rattling handle. What it does:

• Fastens the handle to the door or front panel
• Self-tapping design engages/cuts threads for a secure hold
• Replaces missing, rusted, or stripped handle screws
• Helps correct a loose, wobbly, or rattling handle

• One handle tapping screw

• Disconnect power before service; for gas ranges, also shut off gas
• Support the handle while removing/installing screws to avoid stressing glass or trim
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Keep track of any decorative end caps or spacers for reassembly

This idler pivot screw secures the dryer idler assembly so the belt stays properly tensioned for smooth drum rotation. It's a small but critical mounting fastener for the idler/pulley system. What it does:

• Secures the idler/pulley pivot to the dryer chassis so the tensioner can hold the drive belt.
• Restores proper belt alignment and tension when the original pivot screw is missing or worn.
• Helps stop belt slippage and related noise when the idler assembly is loose.
• Works with the idler/pulley components to allow even, stable drum rotation.

• One idler pivot screw

• Disconnect power (and gas, if applicable) before accessing internal dryer parts.
• Basic hand tools required; retain small fasteners to avoid loss during reassembly.
• If the idler or pulley shows wear, inspect and replace the entire idler assembly rather than only the screw.

This silicon controlled rectifier (SCR) is an electronic switching device used to control power to oven/stove heating circuits, helping the appliance regulate temperature and heat output for cooking performance. What it does:

• Switches and regulates AC power to heating elements for controlled heat
• Enables cycle-based or phase-controlled heating used by oven/range controls
• Common replacement when an element won't heat consistently or unit won't maintain temperature
• Helps stop erratic heating caused by a failed power control component

• Disconnect power to the appliance before inspecting or replacing the SCR
• Observe ESD precautions and handle the component by insulated edges

This screw back housing is a rear housing piece that holds and aligns screws and fasteners on the appliance's rear panel, helping maintain proper panel fit and component placement for safe, quiet operation. What it does:

• Secures rear-panel screws and fasteners to keep the back panel stable and aligned
• Supports adjacent components to prevent rubbing, vibration, or rattling noises
• Restores proper panel fit that can affect airflow or clearance around internal parts
• Helps prevent loose or misaligned panels that could expose wiring or components

• Always disconnect power before attempting any repair.
• Remove the rear access panel and keep track of screws and fasteners; note orientation before removing the old housing.
• Replace with the exact OEM part and reuse correct screws; do not overtighten to avoid stripping the housing.
• If adjacent clips or fasteners are damaged, inspect and replace them to ensure a secure fit.

This Nut-Strip Door Guide secures the door guide/strip to the appliance, helping keep the door aligned and operating smoothly. Replace a worn or missing nut to restore proper fit and prevent the guide from loosening. What it does

• Fastens the door guide/strip to the appliance frame or door
• Keeps the door guide stable to maintain proper door alignment
• Helps prevent the guide or trim strip from shifting or falling off
• Commonly replaced when the guide is loose, missing, or stripped

• Disconnect power to the appliance before beginning any repair.
• Use appropriate hand tools (screwdriver/socket) and avoid over-tightening to prevent damage.
• Inspect the door guide/strip and surrounding fasteners; replace any damaged parts for proper fit.

A replacement M12 x 25 flange bolt used to secure appliance components where a washer-style bolt head is required. Durable fastener that restores proper fit and helps stop movement or vibration in assemblies. What it does:

• Secures panels, brackets or assemblies that use an M12 flange-style fastener.
• Restores proper clamping force when an original bolt is stripped, corroded, or missing.
• Helps eliminate rattling, loose parts, or misalignment caused by a failed fastener.
• Works wherever a metric M12 x 25mm flange bolt is specified by the manufacturer.

• One flange bolt (M12 x 25)

• Disconnect power and follow manufacturer safety instructions before servicing.
• Use the correct socket or wrench to avoid rounding the head; tighten to the appliance manufacturer's torque specification.
• Inspect mating threads and replace if damaged; do not force a damaged bolt.
• If the OEM manual calls for threadlocker or a specific torque, follow those instructions.

A self-tapping screw used to fasten appliance panels and components where a threaded hole is formed as the screw is driven. Provides a secure hold for trim, brackets, and light assemblies during repairs. What it does:

• Cuts its own mating thread in sheet metal or thin plastic to secure panels and brackets
• Helps hold trim, access panels, or internal components in place
• Commonly used where a tapped hole is not present or repair requires a replacement fastener
• Can prevent loose parts and rattles caused by missing or damaged screws

• Unplug the appliance before servicing to avoid electrical or mechanical hazards
• Use the correct screwdriver or bit to avoid stripping the screw head
• Start the screw straight and apply steady pressure; do not overtighten to avoid cracking plastic or stripping metal
• Replace only with the exact part number to ensure proper fit and function

This is a 6-10 x 1/2 inch Phillips pan-head screw used to fasten appliance panels and components. It replaces stripped or missing fasteners so panels and brackets stay securely attached and aligned. What it does

• Secures trim, panels, brackets, and internal components to prevent loosening or rattling
• Restores proper fit and alignment after repair or disassembly
• Helps maintain grounding/connection where screw retention is required
• Common symptom: loose or missing screws causing vibration, rattles, or gaps in panels

• One Phillips pan-head screw (6-10 x 1/2 in)

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct #2 Phillips driver and seat the bit fully to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or damage plastic parts
• Replace with the exact OEM screw for best fit and finish

This is a plated 10-32 x 1/2 inch Phillips flat-head screw used to secure panels and small components on appliances. Durable plating resists corrosion and helps keep assemblies tight and aligned. What it does

• Fastens panels, brackets, and internal components that use 10-32 threads
• Restores a missing or stripped screw to stop rattling or loose parts
• Fits locations that require a 1/2 in. length and flat-head seating for flush finish
• Plated finish helps resist corrosion in typical appliance environments

• Use appropriate 10-32 threaded hole and tighten until snug; avoid over-torquing
• Match head style and length to original fastener for proper fit and clearance
• Turn power off and follow safety precautions before working inside appliances
• If threads are damaged, assess mounting hole and replace or repair as needed

This 10-32 mounting screw secures appliance handles and trim pieces, restoring proper fit and preventing loose or wobbly handles. Use it when a handle feels loose or the attachment hardware is missing or damaged. What it does:

• Fastens handles and related trim to appliance doors or panels
• Restores secure attachment to stop handle wobble or movement
• Replaces stripped, worn, or missing mounting hardware
• Matches OEM thread size for proper fit in mating fastener holes

• One 10-32 mounting screw

• Use the correct screwdriver or bit to avoid stripping the screw head
• Start threading by hand to ensure proper alignment before tightening
• Tighten until snug; avoid overtightening which can strip threads or crack panels
• Disconnect power and follow appliance safety instructions if disassembly exposes electrical components

Nickel

A replacement screw used to fasten internal or external appliance components, restoring secure mounting and eliminating movement. Simple, direct replacement for a single mounting point when the original screw is missing, stripped, or damaged. What it does:

• Secures panels, brackets, or components to prevent vibration and rattling during operation
• Restores proper alignment and stability to assemblies that have a loose or missing fastener
• Helps maintain safety by keeping covers and guards firmly in place
• Common symptom: loose panels, squeaks, or parts shifting during use

• Disconnect power and water before inspecting or working on the appliance
• Use the correct driver or bit to avoid stripping the head
• Thread carefully and tighten until snug; do not overtighten to prevent stripping or damage