Hinge Parts

Supports and guides your range oven door for smooth opening and closing. Replace if your hinge is cracked, broken, or causing door misalignment issues.

Replacement lid hinge for top-load washers. Mounts between the lid and cabinet. Replace when bent, twisted, rusted through, or cracked from wear.

Restore smooth, controlled door movement and a tight oven seal with this door hinge. Replacing a worn hinge helps the door close fully, prevents heat loss, and brings back the original opening tension on top or bottom compartments.

• Controls door swing and spring tension for smooth opening/closing
• Maintains alignment so the door gasket seals evenly
• Helps the door stay closed during cooking and hold at designed positions
• Common symptoms: door won't close fully, drops/sags, uneven gap, squeaks/binds, or heat escaping

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door; support it to safely relieve hinge spring tension
• Note hinge orientation and attachment points; transfer and secure the hinge using existing mounting locations
• After reassembly, verify latch engagement and even gasket contact; many ovens use two hinges—replace in pairs if both show wear

Supports your dryer door and allows smooth opening and closing. Replace if the door sags, has excessive play, won't stay shut, or the hinge is cracked.

OEM mounting bracket that secures the hinge and pin assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Upper hinge assembly for refrigerator doors. Mounts at the top to support and pivot the door. Replace if hinge is worn, cracked, or broken to restore alignment.

Replacement door hinge for dryers. Installs on the door assembly to allow smooth opening and closing. Needed when original hinge is broken or cracked.

Supports and pivots your refrigerator door for smooth opening and flush closing. Replace if hinge is worn, damaged, or causing misalignment issues.

The door stop bracket is a metal or plastic bracket that mounts to the appliance cabinet or door frame to physically limit how far the door can open, protecting the hinges and surrounding cabinetry. It works alongside other door stop components to keep the door from swinging past a safe angle. Replace this bracket if it is bent, cracked, missing, or your door swings open too far and is stressing the hinges.

This bottom hinge replaces the lower door pivot on compatible Frigidaire refrigerators to restore proper door alignment and smooth opening. It provides a secure pivot point to help maintain an even close and consistent seal. What it does:

• Supports and pivots the lower edge of the refrigerator door for smooth opening and closing.
• Helps maintain correct door alignment so the gasket seals evenly.
• Common replacement for doors that sag, bind, or do not close evenly.
• Works with the factory mounting hardware and hinge locations on compatible models.

• Disconnect power and remove food and loose items from the door before starting.
• Always support the door while removing or installing the hinge to prevent injury or damage.
• Use appropriate hand tools and avoid overtightening fasteners; check door alignment after installation.
• Refer to your model's service manual or official parts diagram for model-specific steps and torque specs.

Cushions and limits freezer door movement to prevent over-travel and reduce impact noise. Replace when cracked, worn, or missing to restore smooth operation.

This stop-door is a small replacement door stop that helps control how the appliance door closes and rests, restoring proper door movement and preventing over-travel or binding. What it does:

• Cushions and limits the door's travel to prevent slamming or over-rotation.
• Helps the door align and latch correctly when closing.
• Can reduce door sag or rubbing caused by a worn/missing stop.
• Addresses symptoms such as a door that closes too far, hangs unevenly, or doesn't sit flush.

• High-level, two-person recommended for larger doors; support the door before removing fasteners.
• Disconnect power (and water if applicable) and follow manufacturer safety guidance before servicing.
• Use appropriate hand tools; inspect adjacent hinges and fasteners and replace if damaged.

Right side door hinge for dishwashers. Installs on the right side of the door frame. Replace if bent, broken, or damaged from door falling too hard.

Replacement hinge for refrigerator doors. Mounts to cabinet and door frame to support smooth opening and closing. Needed when hinge is cracked or worn.

This is a left-side lid hinge for a top-load washing machine. It connects the lid to the washer cabinet and allows it to open and close smoothly. Replace this hinge if the lid feels loose, does not stay open, sits unevenly, or if the hinge is cracked or broken.

Center door hinge assembly for bottom-mount refrigerators. Supports the door weight and maintains proper alignment. Replace if cracked, worn, or broken.