Need Help?
Call
Dryer not heating? A failed igniter is the most common cause. This part ignites the gas burner for heat. Watch the video for step-by-step replacement.
I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more
Burner won't spark or ignite? This cooktop igniter electrode creates the spark needed to light gas burners. Simple DIY fix in under 30 minutes.
This is a Montgomery Ward gas range made by Tappan. Parts are no longer offered for this appliance. So, I had to eyeball various ignitors to determine which one would work. I settled on the least expensive one and ordered two (Just in case there were "issues"). The parts arrived quickly but were not a simple drop-in replacement. The new ones were longer and smaller in diameter. I had to use the original bracket because it provided the electrical ground for the spark. I used a spring to... Read more
Fix burners that won't light or spark continuously with this gas range burner igniter electrode. Solves clicking, weak spark, or no-ignition issues.
We replaced both front orifice holders. Very easy to bend and break. If it has a deep bend in it, It will slow down the gas flow to the burner. if you have a low gas flow your burner will burn low So check your small silver gas lines and if you smell gas check your lines Read more
Fix a dryer that won't heat or ignites then cuts out. This igniter assembly lights the gas burner for proper drying. DIY repair takes 30-45 minutes.
I had cleaned the lint out of the dryer exhaust hose, that was usually the problem. But still no heat. I went online to AppliancePpartPros and watched the videos and was able to diagnose that I needed a new ignitor. .The parts delivered very quickly and I had the job done in 15 minutes. The repair place I called would have taken days to come out just to look at it at.. Read more
The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles.
Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines.
Symptoms of a faulty ignitor can include:
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
If your gas range burner sparks but won't light or clicks continuously, this electrode and harness assembly restores ignition. Easy DIY installation.
Ordered new igniters/wires Read more
If your gas oven won't heat or takes too long to preheat, a weak igniter is usually the cause. This oven igniter lights the burner for reliable heating.
Fix a gas burner that won't light or produces weak sparks. This cooktop igniter creates the spark needed to ignite your gas burner. DIY-friendly repair.
The igniter was sparking, but the spark did not appear as bright as the other burners. Swapped the burner and lid since that is where contact is made. Did not help. Came to the conclusion it was a faulty igniter. I ordered parts, replaced the igniter and now the range burner works fine. Read more
If your dryer won't heat or takes too long to dry, a faulty gas igniter is often the cause. This assembly heats up to ignite the burner for proper drying.
Installed a new igniter. Read more
Oven won't heat or takes forever to reach temperature? A weak or failing igniter is the likely cause. This range oven igniter is a 10-minute DIY fix.
I replaced the igniter with a Frigidaire(Electrolux) part. The small oven on my Thermador Pro-Harmony Gas Range stopped heating (on Thanksgiving Day of course). I looked on the internet and I saw a video indicating it may be the igniter. I ordered both the Bosch igniter (00415504) and the Frigidaire (5303935066). Bosch and Thermador are the same company. The Bosch igniter looked like the existing Thermador except the connecting wires were too short. Therefore I used the Frigidaire/Electrolux... Read more
This is an oven bake igniter that mounts inside the oven compartment near the bake burner. It draws electrical current to heat up and open the gas valve, allowing the bake burner to light. Replace this part if your oven takes a long time to heat up, doesn't reach the set temperature, or fails to ignite at all.
Replaced all ignitors. Read more
Burner won't light when you turn the knob? This spark electrode creates the electric arc that ignites your gas burner. Straightforward DIY repair.
Replaced Read more
Fix burners that click but won't light with this gas range surface burner igniter. DIY-friendly repair takes about 10 minutes with basic tools.
First I watched the repair video, and then was successful in changing out two of the Ignitor's on the surface Burners, it worked great ! Read more
Unpredictable or incomplete oven heating? This high voltage electrode and harness assembly transmits electricity to ignition components in your gas range.
Fix a burner that won't light or sparks weakly with this gas cooktop igniter. Remove the burner cap and brass nut to access. Takes 5-10 minutes to install.
Appliance pros had the part. Incredibly, we received it the next day. They sent a confirming e mail with general instructions on how to replace it. Worked like a charm! Our's is a Bosch unit. The retaining brass nut in the center of the burner is an odd size-20 mm which I did not have among my many automotive metric tools. The local Auto Zone though had a 20 mm socket. Once that was removed the procedure would have been a breeze except the retaining screw on the old igniter was frozen. ... Read more
Oven won't ignite or clicks but doesn't light? This bake burner with spark igniter fixes grounding issues and ignition failures. Easy DIY repair.
Replaced igniter under oven floor panel. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.