Support Parts

• Will not agitate
• Burning smell

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

I replaced the suspension rods -- I am NOT particularly experienced with machines of any type, so it took me longer than it might have someone else, but once I figured out what I needed to do, everything went very smoothly. The washer spins like a dream now! Read more

Ordered the parts and followed the instruction videos that Sears provide, Initially tried to order parts from Sears directly but the web-page kept complaining about my shipping address. Their loss- no wonder they're going out of business. Also, should note that the original assembly was plastic but the replacement was metal. Sure sign of a crappy cost-cutting decision. Overall, very happy with Appliance Parts Pros! Read more

Samsung top load washer, about 3 years old started throwing a DC error code more and more often. Initially started with large loads. Wash would get to spin cycle, start wobbling all over the place, stop and refill then try again. Eventually it would stop and throw the DC code. As time went on, the size of the loads got smaller and smaller. Research here indicated that suspension rods probably need replacing. I bought 4 rods for replacement for about $90 in total inc. tax & shipping.... Read more

Replace the sprayer in the middle of the dishwasher, the problem was the grommet on the back of it but it's not available individually. Read more

Replaced all 4 shocks. Read more

So, in the process of a kitchen remodel my GC managed to lose *both* of the rear plastic supports for my GE stove! The drawer was totally unsupported without the brackets. I managed to find them on your site and see that they were a new and better design (rear mount with screw vs side mount and no firm mounting). The install was a snap and the brackets work excellent. I wish I knew that there was a new design years ago or I would have bought them much sooner! Thanks!! Read more

I replaced the suspension rods -- I am NOT particularly experienced with machines of any type, so it took me longer than it might have someone else, but once I figured out what I needed to do, everything went very smoothly. The washer spins like a dream now! Read more

I discovered that the manifold was not connecting with the water supply,so the dishes in the upper tray were not being washed. This was caused because the rear hanger on the manifold had broken and it did not lineup properly into the water supply connection in the back of the dishwasher. I removed the manifold and found that it had two part numbers stamped on it. I searched on both part numbers and received a hit on the second part number. The photo looked exactly like my manifold so I... Read more

Initially I replaced the rear drum bearing assembly. I searched all over for a good how-to video and came across the Appliance Pros tutorial on YouTube. It was by far the easiest to understand with the added bonus that AP had the parts I needed. I had never done this before, but using the video as my guide I was able to replace the rear bearing assembly in about an hour and a half. It would've taken a little less time if I hadn't had to run to the hardware store for a T25 bit. I also could... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more