Need Help?
Call
Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.
Removed some screws, opened the top of the wash machine, unplugged some wires to remove the part, plugged the wires back into the mew part, put the new water valve into place, secured the water valve with the screw, put the top back on the wash machine, and replaced all remaining screws! Real Simple! Read more
Fixes washer not filling, slow fill, or temperature issues. This triple-coil water valve controls hot and cold water flow. DIY repair takes 15-30 minutes.
Ordered the new part and put it back together was a easy fix only took about 15 min. to take apart and put it back. Read more
The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.
Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.
Symptoms of a bad float include:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
Replaced the defective float switch. Read more
Fix a dishwasher that won't fill or overflows with this water inlet valve. Solves filling issues and stops leaks. Moderate DIY repair in 30-45 minutes.
I replaced the valve. Read more
Ice maker not filling or water won't shut off? The water inlet valve controls flow to your ice maker and dispenser. DIY-friendly repair in 30-45 minutes.
Fixed the problem, it is now making ice. Read more
Fix washer filling when off or showing E11 error with this water inlet valve. Controls hot and cold water flow. Moderate DIY repair, 1-2 hours.
Replaced manifold Read more
The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.
Symptoms of a faulty water inlet funnel service kit include:
Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.
I replaced the door seal for the leak. We had a small tear in the sealing surface that resulted in water dripping down the front of the machine (just below the door). I also replaced the detergent dispenser main box with diverter unit. This corrected excessive water being left inside the detergent dispenser at the end of each cycle. I highly recommend replacing the dispenser seal and gasket nozzle to be on the safe side. As these parts are subject to wear and fatigue over the life of the... Read more
Fix leaking dishwasher or water overflowing onto the floor. This float assembly rises with water level to prevent overfills. Easy 5-10 minute repair.
Removed front kick plate, found overflow valve assembly leaking . When parts arrived removed and replaced overflow valve. Took about 10 minutes Read more
Dishwasher not filling with water or leaking? This water inlet valve controls water flow during the fill cycle. DIY-friendly replacement.
Replace old with a new one with a seal in it worked like a new unit. Read more
This valve magnet is the solenoid actuator used to open and close a dishwasher water/control valve, restoring proper water flow for filling and cycle operation. It replaces a failed or weak magnet to help the valve respond correctly. What it does:
The repair is easy. Two screws in the back hold the top cover - once they are off you need to slide the cover back and it comes off. The valve is right there where the cold water hose is connected. Disconnect the control wires / clamp and slide back the wire clamps / remove the two rubber hosed / remove the old valve (it is snapped in place - look at the new one to understand the snap mechanism) / install the new valve. The repair takes less than 10 min. I tested and sure enough... now it... Read more
Oven won't heat or ignite? A faulty gas control valve prevents gas flow to the burner. Moderate DIY repair restores reliable baking in 1-2 hours.
I found I could "rap" on my broiler/oven control valve and the oven would light, so I ordered a new control valve. Installing valve was not difficult except for having to lay on the floor and work in a small space. After installation, the oven lit only ONE time...and the boiler/oven problem was unchanged....broiler would light, but not oven. (Both incandescent pilots would glow brightly, so I did not suspect the igniter/pilot.) A friend suggested I swap ignitors anyway...and indeed, the... Read more
Fix dishwasher water leaks or no water flow issues with this water inlet valve. Controls water fill during wash cycles. DIY-friendly replacement.
Replaced water valve. Using parts pro parts and you tube. Read more
Fix no ice, weak water flow, or leaking with a new water inlet valve. Controls water to your ice maker and dispenser. DIY-friendly repair.
Needed to replace the water valve. Ordered the part Sunday afternoon and it arrived Tuesday morning. Installation was simple especially after watching the online repair video. The most difficult part of the installation process was moving the refrigerator out from its location in order to get access to the back. Read more
Fixes no water to ice maker, slow water flow, or leaking connections. Includes dual valves and bracket. Simple 10-minute repair with basic tools.
Replaced part, had a friend do it for me. I still can't believe the part was here as fast as it was, less than 24 hrs from time I ordered it. great service, thank you Read more
Burner won't light or knob won't turn? This top burner valve controls gas flow to restore reliable ignition and flame control. DIY-friendly replacement.
Called repairman who diagnosed the problem. He said burner valve would cost around $125. I went online and found it for $35. Sears direct cost $43. Repairman installed and works great. Appliance parts was same part for less and shipped overnight for $9. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.