Need Help?
Call
Door solenoid with plunger.
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside.... Read more
Fix dishwasher overflows and leaks with a new float assembly. Controls water level to prevent overfilling. Moderate DIY repair with video guide.
Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more
This is an electrically operated water inlet valve assembly with a built-in vacuum break (backflow preventer) for a washing machine. It controls the flow of hot and cold water into the wash tub when the machine fills during a cycle. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when it should stop, or if you notice water leaking from the valve area.
New valve. Read more
Fix no water to ice maker or dispenser with a new water inlet valve. Restores proper water flow. DIY repair typically takes 10-20 minutes.
Replaced water valve to fix water not going to door, easy enough to do. Replaced icemaker which was corroded inside the cube-forming trays causing black flakes to come off stuck to the ice cubes, and was also leaking causing the water to drip into the ice bucket making one giant ice cube. Ten-minute job, which took an hour and a half. this is a 25-year-old unit and I only had access to the plug on the back of the icemaker, the other end was behind the rear wall. The wire was simply not long... Read more
Fix leaking water or a non-working ice maker with this refrigerator water inlet valve. Moderate DIY repair in 30-45 minutes with basic tools.
I read instructions at your site for the part replacement.. I got the exact part I ordered and got it installed in about 15 minutes. I saved an expensive service call. Great service, and very reasonable part price for an real GE part. Read more
Fix a washer that fills slowly, won't fill, or leaks water when off with this water inlet valve. DIY repair takes about 30 minutes with basic tools.
Put in a valve Read more
Ice dispenser only crushing or not dispensing? This solenoid valve controls ice flow and cube selection. DIY-friendly repair with video guide.
Replaced ice dispenser solenoid Read more
Fix a burner that won't light, leaks gas, or has a broken control stem. This gas valve regulates flow to one cooktop burner. Moderate DIY repair.
Shut off gas. Order part from your helpful (on Sunday afternoon) telephone person. Get part in two days. Replace part. Read more
Fix dishwasher overfilling or not filling with water by replacing the float assembly. Common issue with sticky buildup preventing proper operation.
I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately. Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it... Read more
Ice maker not filling or water dispenser leaking? This water inlet valve controls flow to your ice maker and dispenser. Most DIYers complete in 15-30 minutes.
I researched the problem online and determined it was undoubtedly the water valve leaking. A visit to AppliancePartsPros.com to order the replacement valve and I was ready to go. Actual repair only took 15 minutes. Read more
Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.
Bacteria buildup in the venting assembly and drain hose. Replaced them and it's back to normal Read more
Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.
Removed some screws, opened the top of the wash machine, unplugged some wires to remove the part, plugged the wires back into the mew part, put the new water valve into place, secured the water valve with the screw, put the top back on the wash machine, and replaced all remaining screws! Real Simple! Read more
Burner won't light or flame won't adjust? This gas range burner valve controls flame height and shutoff. Moderate DIY repair restores safe operation.
Watched a couple of videos that closely matched my project. Warranty company couldn't find a service tech in my area so they had to refund my stove purchase. Part cost under $50. Refund: $950!! Read more
Fix a burner that won't turn off, has weak flame, or a stiff control knob. This gas valve controls flow to one cooktop burner. Moderate DIY repair.
I took apart my stove top and front burner assembly and changed out the part I ordered from you guys. Worked great and only cost me a fraction of the price of hiring a repair guy. Thanks a lot! Read more
The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.
Symptoms of a faulty water inlet funnel service kit include:
Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Fixes washer not filling, slow fill, or temperature issues. This triple-coil water valve controls hot and cold water flow. DIY repair takes 15-30 minutes.
Ordered the new part and put it back together was a easy fix only took about 15 min. to take apart and put it back. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.