Washer Parts

• Noisy
• Leaks water

Replaced drain pump. Your video on your web site was very helpful. Read more

****** always make sure the unit is fully unplugged from the power before you do anything with the outside of the unit to work inside of the unit and while you are working inside the unit... Also make sure that you turn the hot and cold water intake valves off and make sure you don't pull too much on the two water intake hoses that lead to your washer because they can leak with too much pressure exerted on either end******* 1. Took top off unit by unscrewing mounting brackets at two similar... Read more

• Burning smell
• Spins slowly
• Pumps but will not spin
• Noisy

Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more

We had a repair man come and tell us the needed repair at the cost of 70.00 I ordered the parts and saved money. Read more

Replaced suspension rods. Read more

Pulled the washer apart (using your videos as a refresher) and found that the plastic coupling between the motor and the transmission had failed. Searched for parts vendors and found your site. Ordered the coupling on-line and went back down to clean up the machine. In the cleaning process I found a damaged thrust washer for the upper agitator and broken drive dogs for that same agitator. I went to the website to see if I could augment my initial order. I did not want to pay shipping costs... Read more

I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time. Read more

Replaced it with a new wash plate. Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

• Will not drain
• Leaking
• Pumps but will not spin

Looked up the part on your website, ordered it, it came in the next day, watched the install video that you provided, installed it in a few minutes, happy wife! Read more

This process was fairly straightforward, it took a couple of hours. I watched a video on youtube and followed the directions. The trickiest part was attaching the diaphragm to the tub. The weights were in the way and made it difficult to seal. I ended up removing the weights and it went on much easier. Read more

I took it apart and found the drain pump motor had come apart. I found appliancepartspros.com and read the reviews for this company. Customers were very satisfied with the parts and service. I ordered the parts (at a savings of over 30% from my local appliance store) and had them in 2 days (YES TWO DAYS). Totally excellent service. Put the washer back together and it works like new. The repair was very easy to do myself and saved me well over $100. I recommend your company to every do it... Read more

Popped off cap on middle of plate inside machine with flathead screwdriver, used a ratchet wrench and socket on bolt, took off plate. Replacement OEM plate was about $88. Got to house in 3 days. Less than an hour total time. Machine was 1 1/2 years old. It had stopped spinning, making noise. Read more

It was a fast fix. its a Maytag Centennial Top load washer. it took me about 20mins to remove the pump and instal the new one.Most of the time was spent moving the washer. Read more

• Shakes and moves
• Noisy

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more