Control Board

Range won't heat or shows F10/F11 error? This electronic control board manages oven temperature and timed cooking. Moderate DIY repair, 30-45 minutes.

If your oven won't heat, the broiler stays on constantly, or timed cooking cycles fail, this mechanical timer restores manual timing and cycle control.

This electronic oven control replaces the console control used to operate a single-convection oven, restoring user inputs and cycle selection so you can reliably set temperature, timers and cooking modes. Ideal when display, touchpad or convection functions fail. What it does:

• Replaces the oven's main user control to allow selection of bake, broil, convection and timed functions
• Restores touchpad/button input and on-screen feedback when controls are unresponsive or blank
• Helps resolve symptoms such as no display, unresponsive buttons, or inability to start bake/convect cycles
• Interfaces with oven components to relay temperature and command signals to the heating system

• One control (single-conv) as shown

• Disconnect power at the circuit breaker before starting any work to avoid shock hazard
• Handle the control assembly carefully; avoid touching circuit board components and use anti-static precautions if available
• Installation typically requires removing the oven console or back access panel and unplugging the old control connector—refer to OEM service instructions

Microwave won't turn on, made popping noise, or smells like burned electrical? The noise filter often fails when solder joints arc or short out.

Fix an oven that shuts off during heating or a timer that won't work. This gas range electronic control board regulates temperature and cooking functions.

Fix an oven with no display, unresponsive buttons, or temperature control issues. This electronic control board restores user input and cycle selection.

Range won't turn on or display shows incomplete numbers? This electronic control board manages cycles and user inputs. Moderate DIY repair, 1-2 hours.

This ignition generator and wiring harness assembly routes power and provides the spark/ignition signal needed for gas appliance burners to light. It replaces a worn or damaged ignition assembly to restore reliable lighting. What it does:

• Sends ignition voltage to the burner igniters and electrodes so burners light reliably
• Routes and secures wiring between the control module and ignition components
• Common failure symptoms: burners won't light, continuous clicking, or intermittent ignition
• Works as the electrical interface between the control and the igniters for safe startup

• One generator and wiring harness assembly

• Disconnect electrical power and turn off the gas supply before starting work
• Follow the appliance OEM diagram for correct routing and connector locations
• Inspect connectors and electrodes for damage and replace if corroded or worn

Controls user interface buttons and display communication with the main board. Replace if the interface board is faulty, unresponsive, or damaged.

This generator is the OEM replacement rotary cam assembly that times and drives mechanical sequences so your appliance operates correctly. It restores proper cycle sequencing to help eliminate failures caused by a worn or damaged cam. What it does:

• Rotates and indexes internal cams/gears to control mechanical switching and timing
• Ensures correct sequencing of cycles and component engagement
• Commonly replaces noisy, stuck, or non-indexing cam assemblies
• Helps resolve symptoms like intermittent operation, failed cycle changes, or mechanical binding

• One generator (rotary cam assembly) as shown

• Disconnect power before servicing to avoid shock or injury
• Access may require panel removal and basic hand tools
• Verify alignment and timing marks during installation for proper operation

Fix unresponsive buttons, blank displays, or error codes with this range user interface control. Moderately easy DIY repair restores touch controls.

Range won't turn on after power outage or displays F1E0 error? This electronic control board manages oven heating, lights, and temperature sensors.

Note: Due to factory variations, please check your original board before ordering. This display control board has 17 buttons on the front. If your original board has 18 buttons, you may need part# EBR89296404 instead.

The Display PCB Assembly is an OEM part for LG ranges and stoves. It is the main circuit board that controls the display panel and oven. This assembly is responsible for operating all electronic functions such as temperature controls, timers, buttons and digital displays.

Causes of a bad display PCB assembly can be water or liquid damage, failure due to surges or spikes in the power supply over time, or due to normal component degradation after heavy use.

Symptoms of a bad display PCB assembly include:

• Faulty or unresponsive control buttons
• Erratic temperature control functions
• Glitches or failures in the digital display
• Inability to operate certain cooking modes

This OEM LG part is also compatible with some Kenmore models.

White

Control panel buttons not responding or stuck? This range keypad assembly restores touch-sensitive controls. Direct replacement for worn touchpads.

Fix unresponsive buttons, blank displays, or partially lit clock numbers on your gas range. Control panel houses the electronic interface and mounting.