General Electric Bracket & Flange

This drawer mounting bracket secures the lower storage/drawer assembly to the range/cabinet, restoring stable alignment and smooth opening. Durable stamped metal bracket used where the drawer frame needs a reliable support point. What it does:

• Provides a secure attachment point for the appliance storage drawer or lower kick drawer
• Keeps the drawer aligned to prevent sagging, rubbing, or uneven movement
• Restores stability if original bracket is bent, broken, or missing
• Helps eliminate rattling or excessive play in the drawer during use

• One drawer mounting bracket

• Inspect surrounding drawer frame and fasteners; replace missing or damaged screws with OEM-specified hardware
• Disconnect power and ensure range is cool and stable before working on lower drawer assemblies
• Minor hand tools typically required; handle sharp edges carefully and wear gloves if needed

This installation bracket secures and positions appliance components during installation, providing a stable mounting point that helps prevent movement and misalignment for long-term, reliable operation. What it does:

• Provides a secure mounting point to fasten panels or assemblies
• Keeps parts aligned during and after installation to prevent sagging or gaps
• Reduces vibration and rattling caused by loose or improperly supported components
• Helps maintain correct clearances for safe, stable operation

• One installation bracket

• Follow the appliance manufacturer's installation instructions and use only the recommended fasteners
• Disconnect power (and gas, if applicable) before starting work
• Verify bracket orientation and fit before final tightening; avoid over-torquing
• Wear appropriate safety gear

This rear level leg bracket replaces the rear mounting bracket that secures a leveling leg to the appliance frame, restoring proper support and helping keep the appliance stable and level for safe, quiet operation. What it does:

• Secures the rear leveling leg to the appliance frame so the cabinet sits evenly
• Restores proper height and prevents the appliance from tilting backward
• Reduces rocking, wobbling, and vibration caused by a damaged or loose bracket
• Helps maintain safe, stable operation under normal load conditions

• Disconnect power (and gas supply if applicable) and move the appliance to a safe, accessible area before starting.
• Support the appliance cabinet so it cannot tip when the rear leg or bracket is removed.
• Use basic hand tools to remove and install the bracket; follow the appliance manufacturer's instructions.
• Inspect the leveling leg and front mounts while servicing; replace any worn or damaged hardware.

This bracket mounting terminal secures the appliance's main electrical terminal block to the cabinet, keeping wiring stable for a safe, reliable power connection. It's a direct-fit replacement where terminal block support is damaged or loose. What it does

• Physically mounts and supports the main terminal block so incoming power wires stay secure
• Keeps wiring strain-relieved to reduce the risk of loose connections or arcing
• Restores a stable electrical connection when a broken or bent bracket causes intermittent power or poor contact
• Helps prevent overheating at the terminal connection by maintaining proper alignment

• One bracket mounting terminal

• Disconnect all power before servicing; lock out and tag if needed
• Use basic hand tools; avoid overtightening terminal screws to prevent damage
• Inspect wiring and terminal block; replace any damaged wires or connectors when present

Replacement mounting bracket that secures internal panels or components to the appliance frame, restoring alignment and stability. Use this bracket to replace cracked, bent, or missing supports that cause vibration or loose parts. What it does:

• Supports and secures panels, trim, or internal assemblies to keep components properly aligned.
• Reduces rattling, sagging, or movement caused by a broken or missing bracket.
• Restores stable mounting after impact, wear, or stripped mounting points.
• Helps maintain proper fit and operation of adjacent parts by providing a solid attachment point.

• Disconnect power (and water/gas if applicable) before starting any repair.
• Basic hand tools required; remove adjacent panels or trim for access as needed.
• Retain original fasteners when possible; replace damaged clips or screws.

This left switch breakwater is a small plastic retainer that holds the console switch assembly in place, keeping switches secure and aligned for reliable control operation. It helps restore proper switch positioning after damage or wear. What it does:

• Secures the left console switch assembly so buttons and selectors operate correctly
• Keeps the switch contacts aligned to prevent intermittent or non-responsive controls
• Helps block debris from interfering with the switch mechanism
• Commonly replaced when the switch feels loose, sticks, or the control behaves inconsistently

• One left switch breakwater

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the control console or panel; follow your model's service instructions
• Handle plastic retainers carefully to avoid cracking; replace if damaged

A lampholder bucket that secures the oven/stove lamp socket and positions the bulb for proper illumination. Replaces damaged or melted lamp housings to restore the light assembly and protect wiring from heat. What it does:

• Holds and aligns the oven/stove lamp socket and bulb in the cavity
• Shields the socket and wiring from oven heat and grease
• Helps ensure stable electrical contact for consistent illumination
• Prevents the bulb from shifting or contacting other components

• Disconnect power to the appliance before servicing to avoid shock
• Replace with the exact OEM bucket to ensure correct fit and heat resistance
• Inspect the lamp socket and wiring; replace any damaged components
• Use basic hand tools; refer to the appliance service manual for disassembly steps

This is a 6-20 x 3/8 in. appliance screw used to secure panels and components. It provides a simple replacement fastener to restore proper fit and stability to the affected area. What it does:

• Fastens appliance panels, brackets, or small components where a 6-20 x 3/8 in. screw is specified
• Replaces damaged, stripped, or missing screws that cause loose panels or rattling
• Restores proper alignment and reduces vibration-related noise
• Matches the original thread size and length used in many factory assemblies

• One 6-20 x 3/8 in. screw

• Use the correct screwdriver or nut driver to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power or take appropriate safety precautions when working near electrical components
• If fasteners mount to plastic, consider using gentle, even pressure to prevent cracking

The Latch/Switch Holder (Right Side) is an OEM component specifically designed for GE microwaves. It is responsible for securely mounting the latch and door switch components on the right side of the microwave door. 

Symptoms of a bad latch/switch holder include:

• Loose, unstable, or improperly functioning door latch 
• Inoperative or faulty door switch preventing the microwave from operating  
• Physical damage or cracks in the holder plastic

Causes can include normal wear over time exposing internal wires, moisture damage compromising electronics or impact damage weakening the holder structure.

This GE replacement is compatible with Hotpoint, RCA, and Kenmore models.