General Electric Bracket & Flange

This lamp bracket secures the oven/range light assembly in place so the bulb and socket stay aligned for reliable interior lighting. It restores a stable fit when the lamp or housing is loose or mispositioned. What it does:

• Holds the lamp socket or housing firmly to the appliance cavity to prevent movement and rattling.
• Maintains proper lamp alignment so the bulb illuminates the cooking cavity as intended.
• Helps reduce intermittent lighting or poor contact caused by a loose bracket.
• Fits into the lamp/light housing area and provides a mounting point for the bulb assembly.

• One lamp mounting bracket.

• Disconnect power to the appliance before starting any repair to avoid shock hazard.
• Remove the bulb and any trim or covers to access the bracket; handle the bulb with gloves or a cloth.
• Typical installation uses basic hand tools; keep track of screws and orientation for reassembly.
• If wiring or the lamp socket is damaged, inspect and replace those components separately.

This motor bracket secures the appliance motor to the cabinet, keeping the motor aligned and stable for reliable operation. It's a direct-fit replacement that restores proper motor support and reduces noise from misalignment. What it does:

• Supports and positions the motor so the shaft and pulleys line up correctly
• Prevents excess motor movement that can cause vibration or rubbing noises
• Helps maintain proper belt/pulley tension for effective power transfer
• Restores secure motor mounting after damage or corrosion

• Follow the appliance service manual for removal and reassembly; secure all mounting hardware to the specified torque.
• Disconnect power before starting work to avoid electrical shock.
• Inspect surrounding mounting holes and fasteners; replace any damaged screws or hardware.
• Check belts, pulleys, and motor mounts for related damage.

This mounting bracket holds a control switch securely in place so the switch operates reliably. Replaces a damaged or broken switch bracket to restore proper switch alignment and tactile operation. What it does:

• Secures the control or door switch to the appliance chassis so the switch can actuate consistently
• Prevents switch movement that can cause intermittent operation or failure to start
• Helps maintain correct switch alignment, reducing false triggers or stuck switches
• Useful when the original bracket is cracked, bent, or has broken mounting tabs

• One bracket switch (mounting bracket) as shown

• High-level replacement: remove power and access the switch area before replacing the bracket
• Check switch alignment and actuator engagement before reassembling the appliance

This bracket support is a small mounting bracket that secures and stabilizes appliance components, helping keep panels and assemblies aligned for proper operation and reduced vibration. It's a direct-fit replacement when the original bracket is broken or missing. What it does

• Provides a sturdy mounting point to hold panels or internal components in place
• Restores proper alignment to doors, panels or assemblies that sit on the bracket
• Reduces rattling or vibration caused by a loose or damaged bracket
• Helps prevent wear or damage from parts shifting during use

• Unplug the appliance and shut off water/gas (if applicable) before starting work
• Use the original mounting screws; replace damaged fasteners as needed
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection

This metal bracket supports and secures the range/oven control panel so buttons and display stay aligned and stable during use. It restores a solid mount and correct panel fit for safe, reliable operation. What it does:

• Secures the control panel to the console so switches and display remain properly aligned
• Prevents the control panel from sagging, rattling, or shifting when using controls or cleaning
• Restores correct spacing and fit for front-facing controls and trim
• Helps eliminate intermittent contact issues caused by a loose panel

• One control panel bracket

• Disconnect power at the breaker before starting any work
• Basic hand tools (screwdriver/socket) are typically required; avoid force when removing trim
• Keep track of screws and clips—reinstall in original locations to ensure proper fit

This bracket belt switch assembly secures the dryer belt switch and helps stop the motor if the belt slips or breaks, protecting the dryer from damage and preventing unsafe operation. It's a direct-fit replacement for the original mounting assembly. What it does

• Holds the belt switch in the correct position so it can sense belt tension.
• Opens the circuit when the belt is loose or broken to stop motor operation.
• Can resolve symptoms like a dryer that stops mid-cycle, fails to start, or runs but won't tumble.
• Restores the original mounting and switch alignment for reliable belt sensing.

• One bracket belt switch assembly

• Disconnect power before beginning—this part is used on electric and gas dryers.
• Basic hand tools (screwdriver/socket) are typically required; keep track of mounting hardware.
• Inspect the belt and pulleys while replacing the bracket; replace any worn parts.

This mounting bracket provides a secure support point for appliance components, restoring proper alignment and stability. Use it to replace a bent, broken, or missing bracket to stop rattling and prevent parts from shifting. What it does:

• Secures panels, assemblies, or internal components in their correct position
• Restores stability to reduce vibration, noise, and misalignment issues
• Replaces damaged or corroded brackets that allow parts to sag or move
• Matches OEM fit and mounting points for reliable reinstallation

• Install with the appliance unplugged or power/gas disconnected for safety
• Keep original fasteners when possible; replace any stripped or damaged screws
• Hand-start fasteners, then tighten to secure without over-torquing