General Electric Bracket & Flange

This Range Cooktop Bracket secures the main top to the appliance frame for a tight, stable fit. Replacing a bent or missing bracket can correct a loose, misaligned, or rattling cooktop and help it sit flush.

• Secures the main cooktop to the chassis to prevent lifting or shifting during use
• Helps maintain proper alignment and a flush fit with surrounding trim
• Common symptoms include a loose or uneven cooktop, rattling, or visible gaps
• Useful when the original hold-down bracket is bent, missing, or damaged

• Disconnect power; for gas ranges, shut off the gas supply before servicing.
• Support the cooktop while replacing the bracket; beware of sharp edges.
• Reuse manufacturer-specified fasteners where applicable and tighten securely without overtightening.

Anti-tip kit.

This dryer bearing bracket secures the drum's rear bearing to keep the drum aligned and rotating smoothly. Replacing a worn bracket can help reduce drum wobble, scraping noises, and uneven drum rotation. What it does:

• Supports and locates the rear drum bearing to maintain proper drum alignment.
• Helps prevent the drum from wobbling, rubbing, or scraping against the cabinet.
• Can reduce or eliminate grinding, squealing, or thumping noises caused by a loose or damaged rear support.
• Works with the dryer's rear bearing assembly to enable consistent drum rotation.

• Disconnect electrical power (and gas, if applicable) before beginning any repair.
• Access typically requires removing the dryer drum and rear bulkhead.
• Inspect the bearing, shaft, and surrounding glides; replace any worn components to prevent repeat failure.

The Microwave Lever is an OEM part for GE built-in and over-the-range microwaves. This metal lever links to the door handle and activates the door switch when the handle is pulled open.

Causes of a bad lever can include wear from daily use over many years. Repeated opening and closing of the microwave door puts stress on the lever and surrounding components. 

Symptoms of a bad lever include:

• Power not disabling when door opened  
• Loose or improper connection to door handle
• Door not shutting or latching completely
• Delayed microwave engagement or shut-off

This GE part is also compatible with Hotpoint, RCA, and select Kenmore models.

This door lever is the user-access handle component that lets the appliance door open and latch reliably. It replaces a damaged or broken lever to restore normal door operation and safe access. What it does:

• Provides the handle/lever action needed to open and close the appliance door
• Restores a secure latch action when the original lever is cracked, worn, or broken
• Stops sticking or slipping that can prevent the door from opening smoothly
• Helps prevent further damage to the door assembly by replacing a compromised lever

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Basic hand tools typically required; access may require removing the door or inner panel
• Inspect surrounding trim and mounting points for damage; replace additional parts if worn

This mounting bracket secures the dishwasher rinse module/dispenser assembly so the dispenser stays properly positioned for reliable rinse-aid delivery. A correctly seated bracket helps prevent dispenser misalignment and related rinse-aid issues. What it does:

• Holds the rinse module/dispenser firmly in place inside the dishwasher tub or door
• Keeps the dispenser aligned so rinse aid can be released as designed
• Helps prevent dispenser rattling, shifting, or partial seating during cycles
• Can reduce symptoms like poor rinsing, visible spots, or uneven rinse-aid release

• Disconnect power to the appliance before starting any work for safety
• Basic hand tools (screwdriver, nut driver) are typically needed; follow OEM instructions
• Align the bracket and secure fasteners without over-tightening to avoid damage

This replacement front evaporator fan motor bracket secures the evaporator fan motor and axial fan blade to the freezer evaporator assembly, helping restore proper airflow and reduce vibration. It's a direct-fit mounting support designed for like-for-like replacement. What it does

• Holds the evaporator fan motor and blade in the correct position for consistent airflow across the evaporator coil
• Keeps the motor stable to prevent excessive vibration or rubbing noises
• Helps maintain proper clearance between the fan blade and surrounding shrouds
• Supports reliable fan operation that assists with proper cooling and frost control

• One front evaporator fan motor bracket

• Disconnect power to the appliance before starting any repair
• Remove interior panels and the evaporator cover to access the bracket
• Inspect and replace any damaged fasteners; tighten mounting screws securely but avoid overtightening plastic tabs
• Handle evaporator fins and the fan blade carefully to avoid damage; test fan operation before reassembling all panels

This angle support is a small metal mounting bracket that stabilizes and secures components inside the appliance, helping keep shelves, panels, or assemblies aligned for reliable operation and safe use. What it does:

• Provides structural support for interior panels, shelves, or trim to prevent sagging or misalignment
• Holds assemblies in the correct position to reduce rattling and vibration during use
• Restores proper fit and clearance when a bent or broken bracket causes shifting
• Works with fasteners to anchor components where a right-angle connection is needed

• Inspect surrounding parts and fasteners; replace any damaged screws or clips as needed
• Use the correct size fastener and torque to avoid stripping or cracking adjacent parts
• Disconnect power and follow manufacturer safety guidelines before working near electrical components