General Electric Support Parts

Control support trim provides a stable mounting point for the oven or range control console and circuit board, restoring proper alignment and helping prevent the control module from shifting or rattling during use. What it does:

• Secures the control console and associated circuit board to the appliance frame to maintain correct alignment.
• Reduces or eliminates loose, rattling, or misaligned control panels that can affect button/knob operation.
• Helps protect the control module from movement-related stress during normal use or door operation.
• Used when the original support is cracked, bent or missing and when replacing a damaged console assembly.

• Always disconnect power to the appliance before beginning any service.
• Access typically requires removing the control/console assembly; retain original screws and mounting hardware if reusable.
• Handle the control board and ribbon cables carefully to avoid damage; avoid touching electronic contacts.
• Test console alignment and operation before fully reassembling trim and tightening fasteners.

This supports assembly stabilizes and supports the washer's internal moving components, keeping them properly aligned to control vibration during wash and spin. Replacing a worn support can restore smoother operation and reduce excessive shaking or noise. What it does:

• Supports and stabilizes the tub/drive system during agitation and spin
• Helps absorb vibration to minimize shaking, banging, and noise
• Maintains proper alignment to prevent rubbing or scraping
• Typical failure signs: excessive vibration, out-of-balance interruptions, knocking sounds, or the washer "walking"

• 1 supports assembly

• Disconnect power and water before servicing; wear gloves and eye protection
• Access the assembly by removing the appropriate cabinet/top or front panel per your model's service information
• Safely support the tub/drive to relieve load before removing fasteners and swapping the assembly
• Transfer any model-specific brackets or hardware as needed; the washer is level before test run

This replacement plate restores the original support and fit for the appliance component it secures, helping stop rattles and misalignment. Use this OEM-design plate when the original is bent, cracked, or missing. What it does:

• Provides a stable mounting surface to secure adjacent parts and assemblies
• Prevents movement that can cause noise, misalignment, or uneven operation
• Restores correct spacing and alignment for panels or elements
• Helps maintain safe, consistent appliance performance when damaged

• One plate

• Disconnect power (unplug or switch off breaker) before starting any repair
• Handle edges carefully; replacement metal parts can have sharp edges
• Verify orientation and alignment before tightening fasteners; use only the hardware specified by the manufacturer

This carrier orifice assembly routes and meters gas to a surface burner so the cooktop lights and maintains a steady flame. It restores proper gas delivery for reliable burner performance and safer operation. What it does:

• Holds the orifice that meters gas flow to the burner for correct flame size and stability
• Ensures consistent ignition and even heating across the burner
• Can address weak, uneven, or inconsistent flames and burners that struggle to light
• Works as the mounting interface between the gas valve/orifice and the burner head

• Shut off gas supply and electrical power before servicing the appliance
• Basic hand tools are typically required; avoid forcing fittings or overtightening

This drawer support holds and guides a refrigerator or freezer drawer so it opens and closes smoothly, restoring proper drawer alignment and stability. It's a direct-fit replacement designed to revive normal drawer function. What it does:

• Supports the drawer on its track so drawers glide without sagging or binding
• Restores alignment when the drawer tilts, sticks, or falls out of position
• Helps eliminate uneven movement, catching, or scraping during operation
• Works with the drawer rail system to maintain smooth front-to-back travel

• One drawer support

• Disconnect power to the appliance before servicing to reduce shock risk
• Remove drawer and any shelves to access the support; follow OEM disassembly steps
• Replacement typically snaps or screws into the existing rail; retain original fasteners if reusable

This reinforcement plate restores structural support where the oven/range door or trim attaches, helping stop sagging and keeping panels aligned for proper sealing and appearance. What it does:

• Reinforces the mounting area so door or trim stays securely attached
• Restores alignment to reduce gaps, drafts, or uneven door closing
• Prevents further wear at stressed screw holes and mounting points
• Stops rattling or vibration caused by loose or damaged support

• Disconnect power before servicing and allow appliance to cool completely
• Remove appropriate access panels or door per the manufacturer instructions
• Handle edges carefully; fasten with original hardware and torque to OEM specs
• If mounting holes or surrounding parts are damaged, inspect and replace any worn hardware

This control support is the mounting bracket that secures the appliance control assembly, keeping the control panel stable and aligned for reliable operation. Replaces a worn or broken support to restore proper panel fit and reduce vibration. What it does:

• Holds the control board/panel in place to prevent sagging or misalignment
• Keeps control knobs and buttons properly positioned for accurate use
• Reduces vibration and rattling that can affect button/knob response
• Can prevent intermittent contact caused by a loose or damaged support

• One control support bracket

• Disconnect power (unplug the appliance or shut off the breaker) before starting any work
• Access usually requires removing the control panel or back panel; keep fasteners organized
• Install with original mounting screws; inspect surrounding clips and hardware for wear

This support is a replacement mounting bracket that helps secure internal components and restore proper alignment for stable operation. It's a direct-fit shaped bracket that replaces worn or damaged supports to reduce rattling and shifting. What it does:

• Provides structural support for internal appliance components to maintain correct positioning
• Prevents movement that can cause noise, misalignment, or premature wear
• Restores secure mounting after damage, helping parts function as intended
• Designed to match OEM fit and mounting points for straightforward replacement

• One mounting support bracket

• Safety first: unplug the appliance or disconnect power before starting work
• Basic hand tools typically required; keep fasteners and orientation noted during removal
• Inspect surrounding parts and mounting points; replace any damaged hardware

This is a right-side guide support that secures and aligns a sliding component so drawers or shelves operate smoothly and stay on track. Replaces a worn or broken guide support to restore proper movement and seating. What it does:

• Holds the right-side guide rail or track in place so the drawer or shelf slides evenly
• Prevents the drawer or shelf from sagging, binding, or falling off the track
• Restores proper alignment when the original guide is cracked, broken, or worn
• Works with the existing rail, clips, and mounting hardware to maintain smooth travel

• Disconnect power or unplug the appliance before accessing internal components
• Access may require removing the drawer, shelf, or front panel—use basic hand tools
• Inspect related clips, rails, and fasteners and replace any damaged pieces for best results

This sensor support is a small mounting bracket that secures an appliance sensor in the correct position for reliable readings and consistent operation. It replaces a worn or broken bracket to restore proper sensor placement. What it does:

• Holds the sensor firmly in place to help maintain accurate measurements
• Prevents sensor movement or vibration that can cause inconsistent readings
• Helps reduce false error codes related to misaligned sensors
• Restores proper sensor positioning after accidental damage or wear

• One sensor support mounting bracket

• Disconnect power to the appliance before beginning any repair
• Handle the sensor and wiring gently; avoid pulling on wires or connectors
• Ensure the sensor is seated in the bracket in the correct orientation before reassembly
• Use the existing fasteners or clips; do not overtighten plastic parts