Need Help?
Call
Fix a leaking water dispenser or no ice production with this dual inlet valve. Controls water flow to ice maker and dispenser. DIY-friendly repair.
We have a built-in KitchenAid KSSC42QKS02. Unlike the other Kitchenaid or Whirlpool refrigerators, our valve is located at the bottom and towards the front of the refrigerator. I actually preferred it to be located at the back like the others. It would've been easier to get to. We had to lower the fridge turning the screws(front of the lower panel), so it would sit on the rollers. Then we just simply roll the fridge out, turn off the supply valve, and install the newly bought valve inlet. It... Read more
Fixes ice maker not filling with water, hollow or small ice cubes, or no ice production. Controls water flow into the ice maker. DIY-friendly repair.
Ordered new circuit board and water pump. Hired a professional to install them Read more
This water inlet valve controls the flow of hot and cold water into the washing machine tub during fill cycles. It contains solenoid-operated ports that open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it shouldn't.
Replaced water inlet valve Read more
Fix ice maker overfilling, water leaks, or no water dispensing. This refrigerator water inlet valve kit replaces older Y-type valves. Video guide included.
I replaced the dual outlet valve which did not fix it then i replaced the inlet valve which fixed it Read more
Fix a dishwasher that won't drain or makes loud buzzing/grinding noises. This drain pump assembly restores proper water removal. Moderate DIY repair.
I drained the dishwasher by hand, disconnected power, water, and drain under the sink. I removed the screws holding the dishwasher in place. I located the pump with the online owners manual and removed it leaving the power connected. I put the machine on the rinse cycle and then hit cancel, the pump is supposed to come on, it didn't, I tried it twice, each time it would start if I manually started it spinning. So I ordered a new drain pump and reversed the removal procedure. Everything worked... Read more
This is an electric solenoid water inlet valve that controls the flow of cold water into the washer. It opens when the washer calls for water during fill cycles and closes to stop flow when the correct level is reached. Replace this valve if the washer is not filling with water, filling too slowly, leaking from the back, or continuing to fill when it should stop.
I first replaced the drain hose, as this seemed to be a common problem with LG. The washer continued to leak, I then noticed it was leaking from the valve assembly, inlet. It took 10 minutes and now the washer works fine with no evidence of water. Read more
The Dishwasher Float Cover Assembly is essential for maintaining proper water levels in your dishwasher. This genuine OEM part ensures reliable performance by accurately regulating the float mechanism. Designed to fit a variety of Samsung dishwasher models, it guarantees a perfect fit and seamless integration with your appliance. The Float Cover Assembly helps prevent water overflows and ensures efficient washing cycles, enhancing the longevity of your dishwasher. Its durable construction withstands daily use, providing consistent operation over time. Easy to install, this part allows you to quickly restore your dishwasher's functionality without the need for professional assistance. By choosing this genuine OEM part, you benefit from the quality and reliability that Samsung is known for. Trust the Dishwasher Float Cover Assembly to provide consistent and dependable operation, ensuring your dishes come out clean every time.
Fix washer water leaking into tub or slow dripping when off. Water inlet valve assembly replacement stops fill valve leaks. Easy DIY repair with video.
I ordered from this company expecting the parts to be later than they said and the parts showed up in 2 days like they said. Just before the Easter holiday even. Amazingly fast. Very satisfied!!! Washer is up and running again. Great job on getting me my parts! Thank you! Read more
This fitting connects the water supply line to your refrigerator's water inlet valve, typically located at the back of the unit. Replace if you notice water leaks around the connection or reduced water flow to the dispenser or ice maker.
Replaced the part. Read more
No water from dispenser or ice maker not filling? This water inlet valve controls flow to both. DIY repair takes 10-20 minutes. Fixes leaks and overfilling.
Ordered both the sets of water valve because both had failed. The ice maker valve failed intially which I ingnored for probably 8months. Then the main failed so no water was getting to the water dispensor. Replacing both sets of solinod valves take about 20minutes Read more
Replace a gas range burner valve that's broken, stuck open, or causing hard-to-adjust flames. Moderate DIY repair requires raising the stovetop.
After turning off the gas and unplugging the electricity, I removed all the burners from the stove top using a 3/16" hex socket. Then used a 1/4" socket to removed two or three screws under each burner which hold the burner base to the bottom of the top panel. Then pulled all the knobs and removed the front panel which was held in by two Phillips screws accessible from underneath the panel. It helps to open the oven door to get at these screws. With the knob panel gone, I removed two screws... Read more
This is a water inlet valve that controls the flow of water into the washing machine during fill cycles. It is an electrically operated valve that opens and closes to allow hot or cold water into the tub as directed by the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
Ordered this part and just changed it out. Not hard once I figured out how to get in to it. Read more
This is an electrically controlled water inlet valve that opens and closes to allow hot and cold water into the washing machine during the fill cycle. It is activated by the washer's control board or timer to regulate water flow at the correct times. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when turned off, or leaks from the back of the machine near the hose connections.
I called AppliancePartsPros to find a replacement water inlet valve. They talked me through finding the clothes washer model number. Once the model number was located, the AppliancePartsPros person on the phone found the correct replacement valve. I received the valve 3-5 days after ordering. I downloaded the clothes washer repair manual and watched some YouTube videos regarding valve replacement. I followed the steps in the repair manual being careful to mark anything I had removed during... Read more
Fix a refrigerator with no water dispenser flow, slow water, or leaking dispenser. This dual water inlet valve controls water to the dispenser and icemaker.
After reading some other reviews that were having a similar problem I ordered a water valve that is located in the lower rear of the refer. The change out took less that ten minutes and was similar to the video. The ice maker now is making ice and seems to be working properly. The repair was made easy with the help of Appliancepartspros. Thanks for the help Read more
Fix a washer that won't fill, overfills, or leaks when idle by replacing the water inlet valve. Most DIYers complete this repair in 15-60 minutes.
The error code indicated the washer wasn't getting any water, although the basket was filling to an unusually high level. After checking the inlet hoses and their connections but without opening the top cover to see the actual water level pressure switch, I went ahead and ordered the part. After receiving the switch, I opened the cover and found the original switch had fallen off it's mounting (for who-knows how long ago) and was resting against the drum. Over time, the movement of the drum... Read more
This water inlet valve controls the flow of water into the washing machine during fill cycles. It uses an electrically operated solenoid to open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
The problem wasn't a blocked screen. I took apart my washer. Very easy on the Kenmore 600 series. Before I did this, I watched a YouTube video and it was a piece of cake. The whole job took me 35 minutes. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.