Search Results

Supports the front drum edge for smooth rotation. Replace when you hear squeaking or scraping sounds. Confirm fit with your dryer model number.

Supports the front edge of your dryer drum for smooth, quiet rotation. Replace when you hear scraping or squealing sounds. Verify fit with your model.

This duct trap redirects and contains exhaust from the appliance's ventilation opening to help guide airflow and capture debris before it enters the main ductwork. It's a direct-replacement service part designed to restore proper vent routing and reduce buildup in the duct path. What it does:

• Funnels exhaust from the appliance outlet into the duct system for proper ventilation
• Helps prevent large debris and lint from entering the main duct run
• Restores correct vent alignment and sealing for efficient airflow
• Commonly replaced when damaged, cracked, or allowing exhaust leaks

• One duct trap

• Disconnect power to the appliance before starting any work; if gas is present, follow gas-safety shutoff procedures
• Access may require removing the rear/discharge panel or lowering the appliance; keep track of fasteners
• Inspect adjoining ductwork and seals; replace or reseal with appropriate high-temp duct tape when reinstalling
• Wear gloves and eye protection

Cushions drum contact points to reduce noise and metal wear in your dryer. Replace when worn, torn, or missing to restore quiet operation. Confirm fit with your model number.

Washer bearing supports drum rotation during spin cycles. Replace if washer makes loud grinding or squealing noises. Verify fit with your model number.

Dryer drum shaft support with shaft assembly. Replace if drum drops, shaft breaks, or squealing occurs from worn bearings. Verify fit with your model.

Supports the washer drum shaft for smooth, stable spinning. Replace if you hear grinding noises or wobbling during cycles. Confirm fit with your model.

The Trap Duct Assembly is an OEM replacement part for GE dryers. This assembly provides the ducting and pathway to direct lint from the dryer drum to the lint trap. It plays a crucial role in efficiently removing lint and preventing blockages. 

Causes of a bad trap duct assembly can include cracks or breaks in the ducting material, crushing or collapsing of the duct, or loose connections that allow lint to bypass the trap. 

Symptoms of a bad trap duct assembly include:

• Increased drying times as lint is not properly exhausted 
• Lint building up inside the dryer instead of collecting in the trap
• Vibrating or rattling noises from loose or damaged ducting
• Reduced airflow leading to inefficient drying performance

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models. Replace yours today for optimal lint removal and dryer operation.

Replacement mounting collar secures and aligns dryer components for proper fit. Replace when worn or damaged to restore original spacing and support.

This Support is a replacement mounting bracket that helps secure the appliance's internal assembly and restore proper alignment for smooth, quiet operation. Use it to replace worn or damaged supports that allow excessive movement. What it does

• Holds and stabilizes internal components to prevent wobbling or shifting during operation
• Helps reduce rattling, grinding, or knocking noises caused by loose supports
• Restores correct alignment to improve part engagement and function
• Prevents premature wear on adjacent parts caused by excess movement

• One Support mounting bracket

• Disconnect power (and gas if applicable) before beginning any repair
• Inspect surrounding fasteners and mounting surfaces; replace any damaged hardware
• Tighten to manufacturer torque specs where available; avoid over-tightening

Supports washer drum for smooth, quiet rotation during spin cycles. Replace if you hear grinding noise or excessive vibration. Verify fit with your model.

This bearing housing assembly supports the washer tub and secures the inner bearing for smooth drum rotation. Replaces worn or damaged upper housing to reduce noise and restore stable tub alignment. What it does:

• Holds the upper bearing and anchors the inner tub to the transmission/drum shaft.
• Maintains correct tub alignment to prevent excessive wobble or vibration during spin.
• Keeps the bearing seated to reduce grinding, squealing, or rumbling noises.
• Helps prevent premature bearing wear that can lead to louder operation or tub movement.

• One upper bearing housing assembly.

• Disconnect power and water supply before beginning service; follow all safety precautions.
• Drain and support the tub before removing fasteners; this may require disassembling the cabinet and removing the agitator/tub per the service manual.
• Inspect bearings and seals when replacing the housing; replace any worn bearings or seals to ensure proper function.

Washer bearing seal kit prevents water leaks into the tub bearing. Replace if you hear grinding noises or see rust on clothes. Confirm fit with model.

The Top Bearing is an OEM part for GE electric dryers. Located near the top of the drum assembly, it further supports rotational movement during tumbling.

Symptoms of a faulty top bearing include:

• Emergence of grinding or scraping noises from the upper drum area
• Resistance or lack of responsiveness to smooth drum spinning  
• Potential impacts to interconnected spinning components  

As a bearing used repeatedly over time, standard wear from lint and dust accumulation affects function. Impacts can also compromise integrity on occasion. 

Causes typically include normal wear and tear from prolonged rotational cycles. Heavy loads may accelerate deterioration too by adding strain.

This genuine GE replacement bearing restores reliable support at the top of spinning cycles. Compatible with some Hotpoint, RCA, and select Kenmore dryers too, it extends equipment life through dependable bearing operation once installed.