Belt

Purchased the items on your site . Did the job myself . Watched your helpful video. Read more

Replaced belt. Read more

I replaced the idler pulley assembly, the bearing plastic and the drive belt. While disassembled I cleaned the interior of the cabinet and lubricated the drum bearings with silicone after cleaning everything thoroughly. The dryer is now quiet and hopefully stays that way. Read more

Found the belt was thrown off. Reinstalled the belt and when doing so felt that the pulley was wobbling on the barrel shaft. Took the pulley off and noticed the inside of the pulley was worn badly and needed to be replaced. When received the new pulley and belt easily installed and was working like new. Read more

I replaced the drive belt using the video instructions on your web site. My dryer is in a stacked configuration, inverted with respect to your instructions with the motor above the drum instead of below it. During reassembly the drum got stuck when the pivot did not seat properly in its socket so the front couldn't be reassembled until I lifted the drum to reseat its pivot so the drum could move back into position allowing the front to be reassembled. The hight of the drum in the stacked... Read more

Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle. Spent a lot of time with shop-vac removing lint from drier and exhaust ducts. Runs great and is no longer cooking or staining clothes. Read more

Tub bearing failure, basically the whole machine has to be taken a part. I've used appliancepartspros in the past so I came back. Quick shipping, parts ordered Thursday night and got here Monday. Take your time or you'll just cost yourself more money. I was lucky in that I did not have to buy the $568 inner tub because I found a bearing and seal kit on Amazon for $80. Historically appliancepartspros' website has been very accurate indicating in stock or not. It appears those days are gone. I... Read more

I replaced the idler pulley, belt and motor! Motor was the main culprit. The motor has faulty centrifugal switches Integrated into the motor. When tumbler begins to turn, the switch kills The motor. The only way to fix it is replace the prefectly good motor, with a New switch inside. Read more

• Pumps but will not spin
• Will not agitate
• Burning smell

I replaced the broken drive belt first and noticed the drive pulley loose. The nut that had held it in place had backed off. This resulted in significant wear on the pulley hub. I just tightened it up and installed the belt. I noticed the belt had a tendency to change its position on the pulley depending on the direction of rotation. I was a bit concerned but decided to see what would happen. This fix lasted for about a week. The belt came off the pulley and broken again. I called a... Read more

Replaced the belt and works GREAT Read more

Replaced the idler pulley assembly. The roller was locking up. Causing it to squeal. I got very lucky the belt was not too worn. Read more

The hardest part of this repair was determining where (controls, motor, belt or transmission) the problem was. I could see little pieces of rubber from the belt beneath the motor pulley, but the machine is 20 years old and some wear is to be expected. Since the belt was still intact and neither frayed or cracked and since I didn't know what the original dimensions were and since the machine was still able to agitate, I could only identify the belt as a possible source of the failure to... Read more

Order set of drum rollers. My dryer required four. As long as I was opening up the dryer, dryer, 10 years old, I wanted to replace all of them. Also ordered new belt for Sam reason. Found full manual online. Disassembled dryer, about 20 screws. Replaced rollers, although only one was squeaky. Put it all back together. Took about 3 hours. Read more

• Will not tumble

Had to replace the drum rollers, idler roller and belt. Machine has never been taken apart so it was a learning event as well as cleaning all the internals components. Parts that were purchased fit fine, no problem with figment. More time was spent oncleaning and prepping the machine for the new parts Read more