General Electric Control Board

This is the electronic range control (ERC) board that manages oven functions like bake/ broil cycles, timers and the front display so your range responds correctly to settings and timing. What it does:

• Controls oven heating elements and cycle selections for bake, broil, and other modes
• Manages clock, timers and front control/display input
• Causes symptoms such as unresponsive controls, blank or error displays, or improper oven heating when failing
• Interfaces with temperature sensors and switches to regulate bake/broil operation

• One electronic range control (ERC) board

• Always disconnect power at the breaker before servicing the range
• Handle the control board by the edges and avoid static discharge; use a grounded strap if available
• Retain original mounting screws and replace panels in reverse order

This replacement timer plastic shaft restores the control knob connection on compatible GE appliance timers so the timer advances and settings stay engaged. Simple, low-cost fix when the original shaft is cracked, stripped, or broken. What it does:

• Replaces the damaged or worn plastic shaft that connects the control knob to the timer mechanism.
• Restores positive knob engagement so the timer advances and selected cycles run.
• Helps eliminate symptoms like a spinning or slipping knob, inability to change timer settings, or intermittent timer control.
• Intended for mechanical/electromechanical control timers that use a plastic shaft interface.

• Disconnect power before servicing to avoid shock or injury.
• Remove the control knob and access the timer per your model's service instructions; handle internal components gently.
• Align the shaft correctly with the timer mechanism and knob splines; do not force parts—inspect for additional damage to the timer or knob.

This inverter assembly is the control module that powers and regulates the refrigerator compressor, restoring variable-speed operation and helping maintain proper cooling. Install to replace a failed or damaged inverter module. What it does

• Converts and supplies the correct power signals to the compressor so it can run at variable speeds
• Can eliminate error codes or fault indicators related to the inverter/control module
• May reduce abnormal compressor noise or intermittent compressor operation when the inverter is faulty

• One inverter assembly

• Disconnect power at the breaker before starting work
• Handle the board and connectors with care; avoid static discharge and damaged wiring
• Verify connector orientation and secure all plugs before reapplying power

This mechanical timer controls cycle duration for the appliance, restoring timed operation and user control. It replaces a worn or non-responsive dial assembly to help the unit advance through programmed cycles reliably. What it does

• Advances and times user-selected cycles so the appliance runs for the intended duration
• Provides tactile dial control for selecting settings and initiating cycles
• Replaces timers that fail to advance, stick, or produce no click/response when turned
• Works with the appliance's control circuitry to signal cycle changes

• One mechanical timer assembly

• Disconnect power before servicing to avoid shock—this part requires access behind the control panel
• Remove control knob and panel fasteners to access and replace the timer; retain mounting hardware if reusing
• Verify wiring positions and take a photo before disconnecting connectors to ensure correct reassembly

This printed circuit is the appliance's electrical control board that manages timed functions and user commands, restoring responsive control and reliable operation when the original board fails. What it does:

• Controls and routes power to user interface, timers, and functional components
• Replaces a failed control board that causes unresponsive buttons or blank/display issues
• Restores correct timing and electronic control when the appliance behaves erratically
• Helps stop intermittent power loss or unexpected cycle interruptions linked to a bad board

• Disconnect power to the appliance before inspecting or replacing the board
• Handle the board carefully; avoid touching components or connector pins to prevent ESD damage
• Verify wiring and connectors match before final assembly; secure all connections

This electronic control board (Quantum) manages oven range functions and user interface features so the appliance responds correctly to cook settings and timers. It restores control panel operation and the appliance's electronic command processing. What it does:

• Serves as the main interface and logic controller for oven/range functions, including bake/broil and timer/clock control
• Processes user commands from the touchpad or selector and sends signals to heating elements, relays, and sensors
• Can fix symptoms such as no display or unresponsive control panel, oven not starting, or erratic cycle behavior
• Works with the oven's sensor and power components to regulate cooking operations

• 1 electronic control board (Quantum) as pictured

• Disconnect power to the appliance before beginning any service to avoid shock or damage
• Handle the board by the edges and avoid static discharge; use proper ESD precautions
• Verify connectors and wiring match before connecting and secure all harnesses firmly
• After installation, restore power and confirm all functions and displays operate correctly

This electronic range control replaces the oven's main control board to restore timed cooking, bake/broil control, and the digital display. It provides reliable management of heating cycles and user interface functions on compatible electric ranges. What it does:

• Controls oven temperature, bake/ broil cycles, and timed cooking functions
• Manages the front-panel display and user inputs for setting temperatures and timers
• Can resolve symptoms such as no display, unresponsive touchpad/buttons, or inability to start bake/broil cycles
• Works with the range's relays to send power to heating elements when requested

• One electronic range control board

• Turn off power to the appliance at the breaker before servicing to avoid shock
• Handle the control board and display assembly carefully to avoid static or physical damage

This washer timer replaces the machine's cycle control knob assembly to restore accurate cycle sequencing and timing. It helps return your washer's ability to advance through wash, rinse and spin selections. What it does:

• Advances washer cycles and controls the sequence of wash, rinse and spin operations
• Sends signals to valves, motor and other controls so selected cycles run properly
• Common symptom: washer won't advance through cycles or stays stuck on one cycle
• Common symptom: controls are unresponsive, or cycles stop before completion

• Disconnect power before servicing to avoid shock — for gas units also shut off gas if applicable
• Verify wiring connections and knob alignment before final assembly; note or photo wires before disconnecting
• Mounts with screws and connects to the washer's factory wiring harness; no universal modifications recommended

This mounted control board assembly regulates key refrigerator functions and replaces a failed main electronics module to restore normal operation. It provides direct control of compressors, fans, defrost cycles and user interface signals. What it does

• Manages compressor and evaporator fan operation to maintain proper cooling; failure can cause no cooling or intermittent cooling.
• Controls defrost cycles and heater operation; faults may lead to excessive frost or failed defrost.
• Processes user inputs and status signals; symptoms include unresponsive controls, blank/erratic displays, or error codes.
• Routes power and communication between system components; failure may cause appliances to not start or behave unpredictably.

• One mounted control board assembly as shown.

• Disconnect power to the appliance before starting any work to avoid shock or damage.
• Handle the board by the edges and avoid static discharge; use grounding precautions if possible.
• Reconnect all harnesses to their original locations and secure the board to its mounting points.

This electronic oven control is the console module that manages the oven's clock, timer, bake/broil functions and user interface. Replacing a faulty control restores reliable temperature control and timed cooking functions. What it does:

• Controls oven bake and broil cycles and interprets user commands from the front console
• Manages clock, delay start, timers and other electronic oven functions
• Can stop oven heating or display error codes when the original control fails
• Commonly replaced when display is blank, touchpad/keys don't respond, or oven won't heat

• Disconnect power at the breaker before starting any work to avoid shock
• Access typically requires removing the oven console or control panel; retain all screws and connectors
• Handle the module and display carefully to avoid static or physical damage

This relay board assembly controls and routes power to key appliance components, restoring reliable switching for motors, compressors, or heating elements. Replacing a failed relay board can resolve intermittent operation and restore normal function. What it does:

• Switches power to major loads so motors, compressors, or heaters run when commanded
• Replaces worn or failed relays that cause intermittent starts or clicking noises
• Helps stop erratic operation or loss of function in affected circuits
• Prevents overloads from passing through a damaged relay assembly (when replaced)

• One relay board assembly

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle the board carefully; avoid touching contacts and use ESD precautions if available
• Verify connector orientation and seat all wiring harnesses fully during reassembly

Please note per GE: Jumper Wire For Phase 2&3 Of Self Clean Must Be Made By Tech In Field "y" Wire. Note:may Have Allign/problem With Holes On Glass,reported(1-18-00) Call On Qualified Technician For Instruction

This generator board supplies the ignition pulse and switching signals for the right/left burner igniters so the range's gas burners light reliably. It replaces a failed ignition control to restore normal spark operation. What it does:

• Generates high-voltage pulses to the right and left burner igniters for ignition
• Routes timing and switching signals between the range's control system and igniters
• Helps stop continuous clicking or lack of spark at the burners
• Addresses symptoms such as no ignition, intermittent sparking, or constant clicking during start-up

• Disconnect power to the appliance and shut off the gas supply before servicing
• Handle the board carefully to avoid static damage; use proper ESD precautions
• Reuse factory mounting hardware and wiring harnesses unless visibly damaged

This electronic main control replaces the appliance's central circuit board to restore normal operation and user interface response. It manages program selection, timing, and communication between sensors and motors for proper cycles. What it does:

• Receives user input and runs the appliance's programmed cycles
• Sends signals to motors, valves, heaters, and sensors to start/stop functions
• Can correct failures like unresponsive controls, incorrect cycles, or error-code behavior when board is faulty
• Helps restore display and touchpad responsiveness when the issue is electronic control failure

• Disconnect all power (unplug or shut off breaker) before starting any work
• Take photos of wiring and connector positions before removal to ensure correct reassembly
• Handle the board by edges and avoid touching circuitry; protect against static discharge

The Encoder Assembly is an OEM part for GE gas ranges. It digitally converts analog knob movements into signals to control the gas valve, igniter, and temperature settings. 

Causes of a bad encoder assembly include degradation of internal sensors and switches over time, loose wiring connections, or impacts that cause misalignment.

Symptoms of a bad encoder assembly are:

• Delays or errors when trying to light burners
• Inaccurate flame height and temperature level responses 
• Knobs feel sticky, sluggish or jump between settings
• Error codes indicating control module communication issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

This thermostat control regulates oven temperature to help maintain consistent cooking heat and safe operation. It replaces a failed TO8 temperature control to restore normal bake/hold functions. What it does:

• Senses and regulates oven temperature to keep cooking cycles near set temperature
• Can stop heating or cause temperature swings when the original control fails
• Commonly replaced when oven won't heat, overheats, or cycles on and off erratically
• Works as the temperature-sensing/control component for the oven control system

• One thermostat control (TO8) as shown

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the control and its terminals carefully to avoid bending or breaking connections
• After installation, verify oven operation and temperature with an oven thermometer