General Electric Heating Element

This replacement heating element restores proper electric heat inside the dryer so clothes dry consistently and on time. A worn or open element can leave loads damp or extend cycle times; swapping it brings heat output back to spec.

• Generates the electric heat used during drying
• Common failure signs: no heat, long dry times, partial heating, or tripping the thermal cutoff
• Visual cues can include broken/warped coil or obvious burn spots
• Restores normal temperature rise for even drying performance

• Disconnect power before servicing; elements run on high voltage
• Access typically from the front or rear depending on model; note wire positions
• Avoid touching the coil with bare hands; handle by the frame
• Inspect thermostats/thermal cutoff if the old element failed

This replacement part is a unit broil assembly, and it is intended for use in different types of ranges or ovens. This is a genuine replacement part made by General Electric. This unit broil assembly is typically found inside an oven or range and is part of the heating mechanisms that allow food to heat or cook. The broiler heats from the top of the appliance and helps with specific things like melting cheese.A new unit broil assembly might be needed if the user notices that the current one is not heating up properly. If the broil element is working the user should feel coming from the broiler area. It is also common to see the broil element turn bright red during use, indicating that there is heat coming off the element. If the element is completely attached but still unable to heat, it might be time to replace this part. Be sure that the appliance is powered off before replacing this part.This part is sourced directly from the manufacturer and is sold individually. This until broil assembly is an OEM replacement part.

This 8-inch surface burner element is the plug-in coil used on many electric ranges. Replacing a worn or failed element restores reliable heating and more even cooking performance on your stovetop.

• Provides heat to pots and pans when energized by the surface control
• Common fix for an element that won't heat or only heats partially
• Addresses visible coil damage such as breaks, blisters, or burned spots
• Corrects intermittent heating caused by an open or failing element

• Disconnect power to the range/unplug before servicing and ensure the element is cool
• Lift the old coil slightly, then pull straight out from the receptacle
• Inspect the receptacle/terminal block and drip bowl; replace if overheated or damaged
• Fully insert the new element terminals into the receptacle, seat the coil level, and test

This 6-inch surface element restores steady, even heat to the small burner on your electric range. Replace a burned-out coil to get back to reliable boiling, simmering, and everyday cooking performance.

• Converts electrical power into heat at the 6-inch burner position
• Helps when the small surface burner won't heat or heats unevenly
• Common signs include visible hot spots, blistering, or burned/loose terminals
• Seats in the drip bowl and connects to the proper surface element receptacle

• Disconnect power at the breaker or unplug the range; allow the element to cool before servicing
• Lift the old element from the drip bowl and pull straight out from the receptacle; avoid twisting or bending the coil
• Inspect the element receptacle for heat damage; replace the receptacle if contacts are burned or loose
• Fully seat the new element and ensure it sits level in the drip bowl before use

This dual radiant surface element sits beneath the glass cooktop and provides two heating zones to match your pan size. Replacing a failed element restores fast, even heating and proper control on the affected burner.

• Heats cookware via two concentric radiant circuits beneath the glass-ceramic surface
• Lets you select inner, outer, or both rings for small or large pans (via the burner control)
• Cycles with its internal limiter to maintain the temperature you set
• Common symptoms: no heat, only one ring heats, uneven or slow heating

• Disconnect power at the breaker before servicing
• Lift/remove the glass cooktop to access elements; support the glass to prevent stress or cracks
• Transfer wiring and any mounting brackets from the old element to the new one, moving one connection at a time and documenting positions
• Test the burner for proper operation before reassembly

Replace a burned-out lower bake heating element to restore consistent heat and even baking. This part is the primary heat source during Bake cycles; when it fails, the oven may not heat, preheat slowly, or bake unevenly.

• Provides bottom heat for the oven during Bake cycles
• Common symptoms: no heat in bake mode, very long preheat, uneven or undercooked results, element not glowing
• Replaces elements with visible cracks, blisters, or breaks
• Restores consistent temperature recovery and even heating

• Disconnect power at the breaker and allow the oven to cool completely
• Remove racks; unfasten mounting screws; gently pull the element forward and move one wire at a time to the new element
• Prevent wires from slipping back into the insulation; support them as you work
• Do not overtighten screws or bend the element; restore power and test Bake

This convection element mounts at the rear of the oven and supplies heat during convection cycles. Replacing a failed element restores consistent, circulating heat for reliable baking and roasting performance. What it does:

• Provides the primary heat source for convection mode at the back of the oven
• Works with the convection fan to circulate hot air for even results
• Helps maintain steady oven temperature during preheat and cycling
• Common symptoms: no heat in convection mode, slow preheat, uneven baking/roasting, or visible damage to the element

• 1 convection heating element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks and the rear interior cover/baffle to access the element
• Note wire locations, transfer existing mounting hardware, and reconnect wires to the same terminals
• Avoid flexing the element; ensure tight connections before restoring power and testing

Restore a large burner on your glass cooktop with this 12-inch Haliant surface element. Mounted beneath the glass, it delivers fast, even radiant heat for big pots and pans and replaces a burner that no longer heats reliably.

• Provides radiant heat to a 12-inch cooking zone beneath the glass surface
• Replaces a failed element that is open, cracked, or burned out
• Typical symptoms: surface burner won't heat or glow, heats unevenly, or works intermittently
• Helps restore consistent heating and proper cycling through the surface controls

• Disconnect power at the breaker before servicing; high voltage is present
• Allow the cooktop to cool completely; handle the element carefully—it's fragile
• Lift the cooktop to access the elements; move wires from the old element to the new one one at a time to match positions
• Ensure the element is centered and secured in the mounting clips before reassembly and testing

This lower bake element restores proper heat in bake mode. Replace a burned-out element to help your oven preheat reliably and maintain set temperatures for consistent cooking results.

• Provides the primary heat source during Bake cycles
• Failure may cause no heat in Bake, long preheat times, or uneven baking
• Visible cracks, blisters, or breaks in the coil indicate replacement is needed
• A shorted element can arc or trip the household circuit breaker

• Disconnect power at the breaker; allow the oven to cool completely
• Remove oven racks; take out the element's mounting screws and gently pull the element forward
• Transfer the wire leads to the new element one at a time; do not let wires retract into the back panel
• Reinstall mounting screws, restore power, and test Bake before replacing racks

This 9-inch dual radiant surface element kit replaces a failed burner on a smooth-top electric range or cooktop, restoring dependable, even heating and letting you choose a smaller or larger heating area to match your cookware.

• Provides two selectable heating zones (inner and outer rings) to match pot size
• Heats cookware evenly across the chosen zone on glass-ceramic cooktops
• Typical symptoms include no heat, only one ring working, slow or uneven heating, or intermittent operation
• Restores burner performance after internal failure of the element assembly

• Disconnect power at the circuit breaker before servicing; 240V shock risk
• Allow the cooktop to cool completely; protect the glass surface while working
• Photograph wiring and transfer leads one at a time to matching terminals on the new element
• Ensure the element seats correctly in its support brackets; test both inner and outer rings before final reassembly

This replacement bake element provides the heat for your oven's Bake cycle. Install a new element to restore fast preheating and consistent temperatures when the original has failed, cracked, or degraded.

• Generates radiant heat during Bake to reach and maintain the set temperature
• Common fixes for: no heat in Bake mode, very long preheat times, or uneven baking
• Replace if the element shows blistering, breaks, or burned spots
• Helps restore proper baking and roasting performance

• Disconnect power to the range before servicing and allow the oven to cool completely
• Remove racks and the oven bottom or shield, take out element screws, and gently pull the element forward
• Transfer wires one at a time and avoid letting wires slip back into the cabinet insulation
• Inspect terminals/wiring for heat damage; do not overtighten mounting screws

This ring-style convection heating element mounts around the fan at the back of the oven and supplies heat for convection cooking. Replacing a failed element helps bring back even air heating and consistent convection bake performance.

• Provides the heat source for convection bake/roast by warming air circulated by the fan
• Helps maintain set temperature and more even results in convection mode
• Common failure signs: no heat in convection while the fan runs, slow or incomplete preheating, uneven baking, visible breaks/blisters, or an open circuit on a continuity test
• Designed to cycle under control of the oven's sensor and electronic controls

• Disconnect power at the breaker or unplug the appliance before servicing
• Access may be from the rear of the appliance or by removing the interior panel over the convection fan, depending on the model
• Label and support the two element leads to keep them from retracting into the cavity; ensure terminals are fully seated
• Reuse existing mounting hardware; avoid bending the new element and verify it doesn't contact the oven cavity

This surface element is the electric heating source for one cooktop burner. Replacing a failed element restores fast, even heat and dependable temperature control on your electric range or cooktop.

• Supplies heat to the selected surface burner when power is applied
• Restores consistent heating and proper cycling after element failure
• Common symptoms: burner won't heat, heats intermittently, or shows visible damage/hot spots
• Often tests open with a meter when failed

• Disconnect power at the breaker before servicing; allow the unit to cool completely
• Protect the cooktop surface; follow your service manual for access to the element
• Note wire positions; transfer wires to the same terminals and reuse existing mounting hardware
• Handle by the frame only; avoid touching the element surface. Reassemble and test operation

This radiant bridge element links two adjacent surface elements on a smooth-top cooktop to create one continuous heating zone for griddles or large pans. Replace it to restore even, reliable heat when the bridge feature stops working.

• Bridges two radiant elements to form a single, continuous heating area for oversize cookware
• Restores proper heat output when the original bridge element is open, damaged, or shorted
• Common symptoms: bridge zone won't heat, heats unevenly across the center, or cycles off immediately
• Intended for radiant glass-ceramic cooktops/ranges equipped with a bridge feature

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Lift the glass top to access the elements; note wire locations and take a reference photo before moving anything
• Handle the element carefully to avoid damaging the heating ribbon and insulation
• Ensure the element sits level and clear of the glass before reassembly, then restore power and test

This radiant bridge element restores heat to the bridge zone on a smooth-top range or cooktop, letting two adjacent burners operate together as one larger cooking area. It replaces a failed element to bring back even, responsive heating.

• Provides the elongated heat source that links two surface elements when the Bridge setting is selected
• Delivers consistent, even heat across larger cookware or griddles
• Replaces a failed or open bridge element to restore normal operation
• Common symptoms: bridge zone won't heat, weak or uneven heating, only works when an adjacent element is on, element tests open

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Lift the glass top or remove the cooktop per your model's procedure to access the element from below
• Note wire positions; move connections to the new element one at a time and secure with existing hardware
• Handle the element carefully; avoid bending or stressing the heating ribbon, verify alignment, then reassemble and test

This dual radiant surface element kit restores two-size heating on your glass-ceramic cooktop or range, delivering even, controllable heat when the original element fails or when only the inner or outer ring works.

• Provides two selectable heating zones so you can match the burner size to your pan
• Replaces a failed surface burner that won't heat or only one ring heats
• Helps resolve slow, inconsistent, or uneven heating on that cooktop zone
• Ideal when the dual function no longer engages or cycles properly

• Disconnect power at the breaker and let the cooktop cool completely before servicing
• Lift the glass top per your model's procedure to access the element
• Move wires one at a time to the new element to maintain correct connections; transfer mounting hardware as needed
• Reassemble and test both inner and outer ring settings for proper operation