General Electric Heating Element

A 12-inch Haliant radiant surface element that restores heating to compatible smooth-glass cooktops. Replaces a failed 12" burner so cookware heats evenly and your range cooks reliably. What it does:

• Heats cookware on smooth-top ranges using a 12" radiant Haliant element
• Replaces a damaged, cracked, or non-heating 12" surface burner
• Common symptoms it can fix: burner won't heat, won't glow, or produces uneven heating
• Matches the original-style heating element for like-for-like replacement

• Disconnect power at the breaker before accessing the cooktop; glass tops can retain heat and pose shock risk
• Handle the glass surface and element carefully to avoid cracking or chipping the cooktop
• Follow the range manufacturer's service manual for correct wiring and mounting; replace only with the exact element specified

This radiant surface element fits a 9-inch dual burner on glass-ceramic cooktops. It restores proper heating and lets you choose inner or full-ring heat, bringing back fast response and even cooking performance when the original element fails.

• Provides radiant heat to the glass cooktop burner area
• Dual design offers two selectable heating zones using inner and outer coils
• Typical failure symptoms: no heat, heats only on one ring, uneven/slow heating, or won't regulate
• Visible breaks or burned areas on the element coil indicate replacement is needed

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift/remove the glass top to access the element; handle glass carefully
• Note wire positions; transfer any mounting brackets/clips from the old element to the new one
• Avoid flexing the element or touching the heating surface with bare hands; verify diameter and terminal layout match the original before reassembly

This 8-inch coil surface element restores reliable heat on electric ranges. Replace a worn or failed burner to bring back consistent heating and everyday cooking performance on your cooktop. What it does:

• Heats cookware at the 8-inch cooking zone by converting electrical power into heat
• Common fix for a burner that won't heat, heats intermittently, or shows visible damage/blistering
• Plugs into the existing surface element receptacle and rests on the cooktop supports
• Helps restore even, consistent heating when the original coil has burned out

• 1 8-inch coil surface element

• Disconnect power at the breaker or unplug the range before servicing
• Allow the element to cool completely before handling
• Lift the old element slightly and pull straight out from the receptacle; avoid twisting or prying
• Align terminals and push the new element firmly into the receptacle until fully seated, then test

This broil element restores the oven's upper heating function so the broiler can produce proper surface browning and high-heat cooking. Replace a damaged or non-heating element to recover consistent broil performance. What it does:

• Provides the high-temperature heat for broiling and top-surface browning.
• Replaces a failed or visibly damaged upper/broil heating element.
• Common symptoms: oven won't broil, food won't brown on top, or the element doesn't glow.
• Visible breaks, blisters, or no heat when broil is selected indicate replacement.

• Disconnect power at the breaker or unplug the appliance before starting.
• Allow the oven to cool completely; wear gloves to protect hands.
• Handle the element and terminals carefully; avoid bending or nicking the heating tube.
• Secure mounting screws and electrical connectors; restore power and test broil function.

The Heater and Housing Assembly is an OEM part for GE electric dryers. As the main heat source, the heater coil works together with the housing to effectively heat air flowing through the dryer. Precisely maintaining optimal drying temperatures is crucial to the drying process. 

Symptoms of a bad heater and housing assembly include:

• Inefficient or prolonged drying times 
• Excessive lint accumulation inside the housing
• Rust or damage visible on the heater coil
• Odors produced from a burnt-out or shorted heater element

Causes can be normal wear over time, moisture damage if the housing is not cleaned regularly, or an internal short if the heater coil is cracked or broken.

This heater and housing replacement is also compatible with Hotpoint, RCA, and some Kenmore electric dryer models.

This 8-inch surface element restores reliable heat to the large burner on an electric range. Replace a worn or open coil to bring back fast, even cooking performance and consistent temperature control.

• Heats cookware on the large 8-inch burner of coil-top electric ranges
• Common symptoms: burner won't heat, heats intermittently, or needs "wiggling" to work
• Visual clues: broken coil, blistering, hot spots, or arcing/burn marks at the terminals
• Helps ensure even heat distribution and stable pan support

• Disconnect power at the breaker and allow the element to cool completely
• Lift the old coil slightly and pull straight out from the receptacle
• Inspect the element receptacle and wiring for heat damage; replace if burnt before installing
• Align terminals and support feet, then push firmly until the element is fully seated

Replacement bridge heating element kit that restores consistent heat across two adjacent cooktop terminals for large cookware and griddles. Replaces a damaged or worn bridge element so your cooktop can heat evenly and reliably. What it does:

• Bridges two adjacent surface element terminals to provide an expanded cooking zone for griddles and large pans.
• Heats the cooking surface where a single element can't cover wide cookware.
• Common symptoms it can fix: one side of a bridged zone not heating, intermittent heat, or visible element damage.
• Works as the direct replacement component to restore normal cooktop heating functionality.

• One bridge heating element replacement kit.

• Disconnect power (unplug or switch off breaker) before inspecting or replacing the element.
• Handle element carefully to avoid bending; use basic hand tools and note terminal connections for reassembly.
• Reconnect wiring securely and verify proper operation after restoring power.

Restore consistent baking performance with this lower-oven bake element assembly. It replaces a failed element so your oven can preheat correctly and maintain even heat during bake cycles.

• Provides the primary heat source in Bake mode
• Works with the oven controls to reach and hold the set temperature
• Common failure symptoms: no heat during Bake
• Extended preheat times or undercooked results
• Visible damage such as blistering, cracks, or breaks in the element

• Disconnect power at the circuit breaker before servicing
• Remove oven racks; take out element mounting screws and gently pull the element forward to access terminals
• Transfer one wire at a time to the new element; prevent wires from slipping back into the oven wall
• Ensure terminals are fully seated and the element is secured before restoring power

This radiant surface element powers the tri-ring burner beneath your glass cooktop. Replacing a failed unit restores reliable, selectable heating across the rings so cookware warms evenly and the burner responds properly to the control. What it does:

• Supplies radiant heat to the cooking zone under the ceramic glass
• Tri-ring design lets you match the heated area to your pan size
• Common failure symptoms: burner won't heat, only one ring heats, uneven/intermittent heating, visible hot spots or breaks under the glass
• Also known in GE documentation as a "Haliant" element

• 1 radiant surface element

• Disconnect power at the circuit breaker; ensure the cooktop is completely cool
• Lift/tilt the glass top per service instructions and support it to avoid stressing the glass
• Move wires from the old element to the new one one-at-a-time to keep connections correct
• Seat the element flat in its brackets and centered under the glass before reassembly

This lower oven bake element provides the primary heat source for Bake cycles, restoring proper preheat and even, reliable cooking. Replace it if the oven won't heat, preheats slowly, or bakes unevenly.

• Heats from the bottom in Bake to reach and maintain set temperature
• Common symptoms: no heat in Bake, very slow preheat, oven temperature too low, or uneven results
• Visual clues: cracks, blisters, or burned spots on the element sheath
• If shorted, it may trip the circuit breaker when Bake is selected

• Disconnect power at the breaker and let the oven cool completely
• Remove racks, take out the element's mounting screws, and gently pull the element forward
• Hold wires so they don't retract; transfer and firmly connect the terminals; replace any heat-damaged connectors
• Reinstall element, ensure it's not contacting the cavity, restore power, and test Bake

This bake element restores even, reliable heat in the lower oven during the bake cycle. Replace it if the oven won't heat, struggles to reach temperature, or the element shows visible damage.

• Provides the primary heat source for baking in the lower oven cavity
• Common symptoms: no heat in bake, slow preheat, not reaching set temperature, uneven baking, or visible blistering/burn spots on the element
• Converts electrical energy to radiant heat for consistent oven performance

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks; take out element mounting screws and gently pull the element forward
• Support and transfer wires one at a time to the new element; ensure tight, secure connections
• Reinstall, restore power, and test for proper preheat and even heating

This lower bake element restores consistent bottom-heat for proper baking and preheating in electric ranges and wall ovens. Replacing a failed element helps eliminate undercooked centers and uneven results.

• Provides primary bake heat from the bottom of the oven cavity
• Common failure signs: no heat in Bake mode, very slow preheat, uneven baking, or visible damage
• Helps ensure stable oven temperatures when paired with a working broil element and thermostat
• Direct-fit replacement designed to connect to existing wiring and bracket mounting

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and transfer wires one at a time to the new element
• Avoid stressing or loosening terminal connections; secure the bracket firmly
• After reassembly, restore power and test Bake to verify proper operation

This Miraclon heater is a direct-replacement heating element assembly that restores proper heat generation in compatible appliances. It provides reliable, OEM-matching heating performance to help your appliance reach and maintain operating temperatures. What it does

• Replaces the appliance's failed internal heater assembly to restore heat production.
• Heats quickly and evenly to support cooking, drying, or defrosting cycles (depending on appliance).
• Common symptom: no heat or weak heat during normal operation.
• Common symptom: appliance runs but items fail to warm or dry as expected.

• Disconnect power and gas before starting any repair.
• Handle the heater carefully; avoid bending or damaging terminals and mounting tabs.
• Follow the appliance service manual for access, mounting, and wiring instructions.

Warming Element

Restore reliable oven heat with this bake element. It produces the lower-oven heat during the Bake cycle, so replacing a failed element brings back normal preheat times and consistent, even results.

• Supplies primary heat from the bottom of the oven during Bake
• Common fix for: no heat on Bake, very slow preheating, uneven baking/browning
• Replace if the element is blistered, cracked, pitted, or has visible breaks
• Helps restore accurate, stable baking temperatures

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; take out the element's mounting screws to free the bracket
• Gently pull the element forward; transfer one wire at a time using insulated pliers and prevent wires from slipping back
• Re-secure the bracket/screws, ensure snug connections, restore power, and test Bake

Dual-zone radiant cooktop element that restores two-size heating on smooth-top electric ranges, allowing burners to match small or large cookware for more even heating and improved cooking control. What it does:

• Provides two concentric heating zones so you can use different pan sizes without losing heat where you need it.
• Heats through the ceramic glass surface using a radiant element positioned beneath the cooktop.
• Replaces a worn, damaged, or non-heating surface element to restore proper burner performance.
• Common symptoms this part can address: a burner that won't heat, partial heating (only inner or outer zone works), or visible element damage under the glass.

• Always disconnect power at the breaker before servicing to avoid electric shock.
• Handle the glass top and element carefully to avoid cracks or damage; do not operate if the glass is cracked.
• Ensure the element is fully seated and electrical terminals are secure before restoring power.