General Electric Hose Or Tube

This is a hose chamber, or dishwasher hose pump. This part attaches to the back of the dishwasher and is the direct line for the water to get in and out during the washing cycle. This specific part prevents leaking and is very important to the machine. The user might need to replace this part if the dishwasher is leaking, if the machine is not putting in or draining water properly, or if the machine has stopped working altogether. Anyone can complete this repair with basic household tools such as a screwdriver, pliers, and working gloves. Always make sure the machine is empty of dishes and is drained of water before starting the repair. Also make sure it is unplugged from the electrical source and is turned off completely. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from manufacturers like General Electric, Hotpoint, RCA, and more.

This drain inlet hose carries wastewater through the washer's internal drain path during drain and spin cycles. Replacing a cracked, kinked, or leaking hose helps restore proper draining and protect floors and nearby components from water damage. What it does:

• Routes drain water between internal components to the drain outlet
• Maintains a sealed flow path to help prevent leaks
• Common symptoms: water on the floor during/after draining, standing water left in the tub, visible cracks/bulges/kinks on the hose
• May clog with debris, restricting flow and causing slow or no drain

• 1 drain inlet hose

• Unplug the washer and shut off water supply before servicing
• Have towels or a shallow pan ready; residual water may spill when hoses are removed
• Note hose routing and clamp positions; ensure the new hose is fully seated and not twisted or kinked
• After installation, run a quick drain/spin and check all connections for leaks

This washer drain hose carries used water from the tub to your home drain. Replacing a cracked, clogged, or kinked hose helps restore proper draining and prevents leaks during the drain/spin portion of the cycle.

• Routes wastewater from the washer to the household standpipe or laundry sink
• Damage or blockage can cause leaks, slow or no draining, or water on the floor
• Replace if you see cracks, splits, bulges, or persistent leaking at the back of the washer
• A pinched or flattened hose can also lead to standing water after a cycle

• Unplug the washer and turn off water; place towels or a pan to catch residual water
• Note the routing; loosen clamps and remove the old hose from the washer outlet and drain connection
• Install the new hose and secure with clamps; avoid kinks or sharp bends
• Verify correct drain height/air gap to prevent siphoning, then run a drain/spin to check for leaks

This 10-foot dishwasher drain hose routes wastewater from your machine to the sink drain or disposer. Replace a cracked, kinked, or too-short hose to restore reliable, leak-free draining and accommodate longer drain runs.

• Conveys drain water from the dishwasher to the household drain/disposer
• Helps address leaks from brittle, split, or loose hoses
• 10-foot length provides extra reach for extended routing

• Disconnect power and turn off water before service
• Route with a proper high loop or air gap per your model manual and local code to prevent backflow
• Avoid kinks; secure connections with appropriate clamps and ensure tight fits
• Run a test cycle and check all connections for leaks

This plastic water tube routes water inside your refrigerator to the dispenser and/or ice maker. Replacing a cracked, brittle, or leaking tube restores proper water flow and helps prevent leaks and water damage.

• Directs water between components such as the inlet valve, reservoir, door, dispenser, or ice maker (varies by model)
• Maintains a sealed, food-grade path to prevent leaks and air intrusion
• Damage can lead to puddles behind/under the fridge or inside the fresh food compartment
• Common symptoms: slow/no dispenser flow, ice maker not filling or making small cubes, visible cracks/kinks

• Unplug the refrigerator and shut off the household water supply; relieve line pressure at the dispenser
• Note tube routing and connection points before removal; avoid sharp bends and kinks during install
• Cut tube ends square and fully seat into compression or push-in fittings
• Restore water, check all joints for leaks, and run water to purge air from the system

Replacement unicouple assembly that connects your portable dishwasher to the sink faucet. It supplies fresh water and routes drain water back to the sink, restoring proper fill/drain and a tight, drip-free connection when the original wears out.

• Provides a quick-connect link between the dishwasher and sink faucet
• Supplies fresh water to the unit and returns drain water to the sink
• Helps maintain a sealed, drip-resistant connection at the coupler
• Often resolves: leaks at the faucet or hose, won't fill/slow fill, won't drain/backs up, coupler won't stay attached

• Unplug the dishwasher and turn off the faucet/water supply before service
• Place towels or a pan to catch residual water; relieve pressure at the sink
• Move the unit to access hose connections; match the original routing and secure clamps firmly
• After installation, attach to the faucet and run a short test to check for leaks during fill and drain

This replacement 5/16-inch icemaker tubing carries water to the ice maker. It helps restore proper flow and reduce leaks when the original line becomes brittle, cracked, or kinked, improving ice production reliability. What it does:

• Carries water from the inlet valve to the icemaker
• Replaces tubing that is brittle, cracked, or kinked
• Helps restore normal icemaker fill and ice production
• Can help stop leaks caused by a damaged water line

• 1 icemaker water tube (5/16 in.)

• Unplug the refrigerator and shut off the water supply before servicing
• Place a towel or container to catch residual water during line removal
• Route the new tube along the original path; avoid sharp bends and hot or moving components
• Tighten all fittings, restore water, and check all connections for leaks before powering on

This drain line assembly routes condensation/defrost water from the refrigerator cabinet to the rear drain pan. Replacing a cracked, warped, or clogged line restores proper drainage and helps prevent interior leaks and ice buildup.

• Directs meltwater from the evaporator drain to the condenser/drain pan
• A restricted or damaged line can lead to water under crispers or on the floor
• Ice sheet forming at the bottom of the freezer is a common sign of a blocked drain
• Restores correct moisture management and helps reduce odors from standing water

• Unplug the refrigerator and turn off the water supply if applicable
• Pull the unit forward and remove the lower rear access cover to reach the drain outlet and pan
• Place a towel, disconnect the old line, clear any ice/debris in the drain channel, and seat the new line fully
• Route the tube into the pan without kinks, reassemble, and verify flow by pouring warm water through the interior drain

This pump hose and clamps create a sealed connection between the dishwasher's pump and internal plumbing. Replace when the hose is cracked or clamps are corroded/loose to stop leaks and restore a secure, watertight fit. What it does:

• Creates a sealed connection between the pump and internal plumbing
• Helps contain water flow during wash and drain operation
• Replace if the hose is cracked, brittle, swollen, or deformed
• Symptoms include water leaking under the dishwasher or loose/corroded clamps

• Disconnect power and water; pull the dishwasher forward as needed for access
• Expect residual water—protect flooring and have a towel or pan ready
• Remove old clamps and hose; fully seat the new hose on fittings, then position and secure clamps at the bead/ridge
• Run a brief cycle and check for leaks before reinstalling

This genuine replacement fill hose routes incoming water from the inlet valve to the dishwasher tub, restoring proper water delivery for washing cycles. Replaces worn or cracked hoses to help stop leaks and ensure reliable fill performance. What it does:

• Carries water from the inlet valve to the dishwasher tub during fill cycles
• Restores proper water flow when original hose is leaking, split, or clogged
• Helps prevent water damage caused by deteriorated or cracked hose sections
• Works with the dishwasher's fill and wash functions to maintain normal operation

• Disconnect power and shut off the household water supply before starting
• Inspect clamps, grommets, and fittings and replace if damaged
• Route hose without kinks and secure with proper clamps to avoid leaks

The drain pump hose assembly is an OEM part for GE washers. This assembly includes the drain hose, clamp, and connector, providing a complete installation for efficiently draining water from your GE washer. It is designed to withstand the water flow and pressure, providing a reliable connection between your washer and the drainage system to prevent water leaks or spills in your laundry area.

A bad drain hose assembly can occur due to wear and tear, clogs, or damage to the hose or connectors. If you notice symptoms such as water leaks, slow or incomplete drainage, or visible cracks or leaks in the hose, it may be time to replace the assembly.

Symptoms of a bad drain hose assembly include:

• Water leaks during the wash or spin cycles
• Slow or incomplete drainage
• Visible cracks or leaks in the hose or connectors

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This water injector fill hose connects the household water supply to the refrigerator's water/ice system, restoring reliable water flow for dispensing and ice production. Designed as a direct replacement to restore proper fill operation. What it does:

• Delivers water from the inlet to the ice maker/water dispenser assembly.
• Restores proper water fill for ice production and dispenser use when the hose is damaged or leaking.
• Helps stop leaks, sputtering dispensers, or slow/irregular ice fill caused by cracked or blocked tubing.
• Works with the refrigerator's injector/fill pathway to maintain consistent water delivery.

• One water injector fill hose.

• Disconnect power and shut off the water supply before installing.
• Inspect and replace any worn clamps or connectors; tighten fittings to prevent leaks.
• Avoid kinking the hose; route it following the original path to prevent flow restriction.

This drain hose directs wastewater away from the appliance to the household drain, helping prevent standing water and poor drainage. Durable, flexible construction lets you route the hose for a secure connection. What it does:

• Carries wastewater from the appliance pump to the household drain or garbage disposal
• Restores proper draining when the existing hose is cracked, split, or clogged
• Helps prevent leaks and water pooling caused by damaged or collapsed hoses
• Allows proper routing to avoid kinks that can restrict flow

• Disconnect power to the appliance and turn off the water supply before starting
• Inspect hose clamps and connections; replace clamps if corroded or loose
• Route the hose without sharp bends or kinks and secure per the appliance's routing path