General Electric Hose Or Tube

This inlet hose connects the household water supply to the appliance's steam generator, allowing steam cycles to produce moisture for cleaning or sanitizing. Replacing a damaged inlet restores proper water flow to the steam system. What it does

• Channels incoming water to the steam generator assembly so the unit can produce steam.
• Stops steam or steam-cycle operation when cracked, pinched, or leaking.
• A leaking or split inlet hose can cause visible water under or behind the appliance.
• Faulty inlet hose may trigger steam-related fault/error indications or interrupted steam cycles.

• One hose inlet for the steam generator assembly.

• Turn off water supply and disconnect power before servicing.
• Inspect and replace any worn seals or O-rings; ensure fittings are seated and tightened to OEM torque specs.
• Use only the exact replacement part number to ensure proper fit and function.

This hose overflow kit redirects excess water from the refrigerator's drain area to the drain pan, helping prevent puddles and water damage behind or under the appliance. Fits common GE refrigerator drain/overflow applications. What it does

• Provides a dedicated path for excess defrost and condensation water to the drain pan
• Helps stop water pooling under or behind the fridge that can indicate a blocked or misrouted drain
• Useful when replacing a cracked, split, or missing drain/overflow hose
• Restores proper water routing after service to the defrost drain or water system

• One hose overflow kit

• Disconnect power and shut off the water supply before starting service
• Route hose from the drain/overflow outlet to the drain pan following OEM routing; secure with supplied clamps or retainers
• Inspect or replace any related grommets or seals to ensure a watertight fit
• Test for proper drainage and check for leaks after restoring power and water

Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.

This 10-foot drain hose routes wastewater from your dishwasher to the sink drain or disposer. Replace cracked, kinked, or too-short hoses for longer runs.

Replacement 5/16-inch water tubing that connects the inlet valve to the icemaker. Replace when the original line becomes brittle, cracked, or kinked.

Replaces the hose and clamps connecting the pump to internal plumbing. Install when the original hose is cracked, split, or clamps are corroded or loose.

Siphon pipe for washer drain air-break assembly. Prevents backflow and unintended siphoning. Replace if cracked, broken, or missing from detergent dispenser.

Routes water from inlet valve to tub. Replace if cracked, leaking at connections, or worn from age. Installs between valve and tub exterior connection point.

This water injector fill hose connects the household water supply to the refrigerator's water/ice system, restoring reliable water flow for dispensing and ice production. Designed as a direct replacement to restore proper fill operation. What it does:

• Delivers water from the inlet to the ice maker/water dispenser assembly.
• Restores proper water fill for ice production and dispenser use when the hose is damaged or leaking.
• Helps stop leaks, sputtering dispensers, or slow/irregular ice fill caused by cracked or blocked tubing.
• Works with the refrigerator's injector/fill pathway to maintain consistent water delivery.

• One water injector fill hose.

• Disconnect power and shut off the water supply before installing.
• Inspect and replace any worn clamps or connectors; tighten fittings to prevent leaks.
• Avoid kinking the hose; route it following the original path to prevent flow restriction.

This 10-foot drain hose kit connects your dishwasher to the household drainage system with a smaller drain port connection. It allows proper drainage of wash water and prevents backflow into the dishwasher. Replace this part if you notice water backing up into your dishwasher, poor drainage during cycles, or if the existing hose is damaged or too short.

Replace your washer's tub hose if it's cracked, leaking, or worn. This hose connects internal components to the tub for proper water circulation.

This pump hose channels washer tub water to the drain pump, restoring proper drainage and preventing leaks at the pump connection. Durable flexible tubing designed to match factory fit and routing. What it does:

• Transfers wash water from the tub to the drain pump for normal draining
• Replaces cracked, collapsed, pinched, or leaking pump hoses that cause poor drainage
• Helps stop leaks that can occur where the tub outlet connects to the pump
• Restores reliable water flow when the original hose is brittle or damaged

• Disconnect power and water before installing; follow all safety precautions
• Inspect clamps and surrounding fittings; replace clamps if damaged or corroded
• Ensure proper routing and secure clamps to avoid kinks or contact with moving parts
• Test a short cycle after installation to check for leaks

Replaces a damaged or worn washer hose and spring assembly. Installs in the drum area. Order this part if your original hose is cracked or leaking.

Replace your washer's pressure switch hose if cracked, kinked, or leaking. This tube connects the pressure sensor to the tub for water level control.