Heating Element

• Too hot
• tripping breaker

I found the assembly with heater element, thermostat, and the thermal fuse already assembled (cheaper than finding what part was bad and ordering that one part). unplugged dryer, pulled it out and removed the dryer exhaust tube, the top and front. The harness was a little short so I wasnt able to pull the whole heater assembly out before disconnecting. BEFORE disconnecting I took a picture so that if my brain forgot what wires went were!!!! put the dryer back together and put a load that just... Read more

Found the part number, went to AppliancePartsPros.com and found it within minutes. I ordered the part and it showed up at my house the following day, no special overnight shipping charges. I changed out the element in about 15 minutes. Great experience with AppliancePartsPros.com. Read more

Range has no model ID plate anywhere. Flip off electric at circuit breaker box. Opened top of range and noted details of the faulty burner, including confirm that outer coil was fried. The maker info on back of element was useless in finding replacement: more useful was general shape, and the numbers around edge on back. Close up range, since low heat element still working. Turns out all Maytag double oven Gemini ranges use the same hi-low element, but double check appearance just in... Read more

Removed the defective burner labeled the leads as to their location and coil connections. Replaced the connections to the corresponding locations, 1 to 1, 2 to 2 and the bridged terminal as it was. I noticed that the coils in the replacement burner were not wound in the same direction as the original burner and made note of this. I did not think much of this at the time, but on turning the power back on and lighting up the burners I noticed up they were not lighting up the corresponding... Read more

Turned stove breaker off in the main breaker box and also unplugged the oven from the 220 outlet. pulled the baking racks out of the oven and proceeded to locate the 1/4 screws just above the bake element where it passes through the metal wall and removed them. pulled the element forward until the wires were exposed and unplugged them and then attached the new element to the wires and reinstalled in reverse order. Read more

Removed the element "easy just four screws" unplugged two connecting wires, removed element. Did a "continuity test" on element, it failed, so I ordered a new one and installed it. It works great now. Read more

Ordered part and installed it. Broiler works as advertised. Read more

• Little to no heat when baking
• Oven not heating evenly

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Would advise before doing this repair to watch the video for it. It is not a plug in connection anymore like older ovens. The key is to keep the connecting wires from the oven from falling or pulling into the inner wall of the oven. The wires may not come very far out away from the wall of the oven so make sure to secure them. The video shows a good way to do that. If you have an in wall oven this is very important because it would hard and time consuming to pull the oven out of the wall to... Read more

Replaced the elements with new ones ordered through Appliance Parts Pros. I wanted to tell you how pleased I am that I ordered the baking and broiler elements for my Maytag oven from you. Your website diagrams for my model of oven helped immensely in figuring out what parts I needed. Your order process was easy and the parts arrived within two days just as stated. Best part of all, the new elements work perfectly! I will bookmark your site for future appliance part needs and I look forward to... Read more

It was very easy caled up ordered the part no prblem got it in 3 days.Got a phillips screw driver removed the top of the stove took out the old one a put in the new one had it fixed within minutes very easy diy no need to pay someone alot of money for this easy fix. Read more

We ordered a new elimate, which was shipped the same day. Very good. Read more

• Element will not heat

I diagnosed the problem, found Appliance Parts Pros and watched their video. It was as easy as the video they made said it would be. Overall an amazing experience. I was quoted $250 to have the repairman come do the same thing. My cost was $40. Read more

In the middle of Christmas baking, I noticed that it was taking a really long time to bake bread. Since I had already done 5 batches and the timing was always the same, I knew when I had to add 20 min, something was wrong. My oven thermometer (I bought at target) no longer worked so it was hard to tell the exact temperature. First, I went and bought a new thermometer to see the actual temp, then I set the oven to 350 degrees and checked to see what the thermometer was showing. It was almost 50... Read more