Lg Parts

• Will not drain
• Noisy

It was fairly obvious that the washer drainer motor had failed, water was not draining, filter was clean (bottom lower left panel door, have a pail ready!) and drain line was not blocked. Someone had provided great advice on the Appliance Parts Pro's site about replacing the drain motor from the bottom. Great suggestion! Easy to do, although be prepared for more water to drain from the washing machine onto the floor after you lay it over. I carefully lowered the machine onto it's back,... Read more

I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more

• Will not stop filling with water
• Leaking
• Shuts off too soon
• Will not fill with water

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more

• Will not tumble

I disassembled/reassembled the dryer according to the ApplianceParts Youtube video. With my limited electrical knowledge (just enough to be dangerous) I initially figured it was a problem with the heating unit, sensor(s), or the control board. After diagnosing the problem (bad thermistor), I had to order the parts and was able to repair and reassemble the dryer several days later. After removing the drum, I cleaned all the dust etc. out of the inside (it gets dirty in there!) and inspected,... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

• Won't start
• No heat
• Little to no heat when broiling
• Oven not heating evenly

We were getting an intermittent F19 code on our lower oven mainly. This code gets triggered when the oven fails to heat up to a minimum temperature within a specific amount of time. I figured this was being caused by an ignition failure so I bought this new ignitor. As it turns out, if you have a double oven then you will have two ignitors. Just keep that in mind in case you are thinking about replacing both or you are seeing errors in both ovens. The ignitor in the lower oven is located below... Read more

I watched the video that was shown on this website to slide the top back, remove the control panel, remove the front panel of the washer, remove the old gasket (the two tension springs are easy to get off, not as easy to replace), cleaned out years of gunk and soap that had built up behind the gasket for 10 years as well as under the rollers in the drum (each roller has a screw, remove it, slide the roller assembly forward and lift up to take off the rollers, and the roller can be broken down... Read more

• Leaking
• Not dispensing water

I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more

• Leaking

Removed the old line and replaced with the new. This is the sixth time I've replaced the line. Yes you read that right, the sixth time. Lines fail about every 6-8 months so I can change one out now in about 10-15 minutes. Bought the refrigerator in Feb '09 and the line first failed in March 2012. Since then I've had failures in as little as 4 months to as much as 9 months. Frustrating to say the least, but I'm a whiz at changing out the line :-) Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

• Lid or door won't close

This was a super-easy repair. You have to line up the spring so that it sits on the bumps inside the magnet holder and the door, then you have to line up the tabs on the magnet holder so they will slide into the slots on the door. Then you just push it in. Repair took less than a minute. Read more

We had a problem of lint building up inside of the filter slot. Once I took a long brush and cleaned the recess where the filter slides I was able to see that the old filter was not catching all the lint. Upon closer examination I noticed that the seal around the filter had become compressed. that's when I order another filter from AppliancePartsPros.com. My new filter came within three days and my dryer has been working fine ever since then. Read more

Searched the internet and found that the culprit could be 3 different parts. Ordered them and fixed the issue by replacing the thermostat! Read more

Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more