Lg Parts

• No heat or not enough heat
• Won't start

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more

• Will not tumble

I disassembled/reassembled the dryer according to the ApplianceParts Youtube video. With my limited electrical knowledge (just enough to be dangerous) I initially figured it was a problem with the heating unit, sensor(s), or the control board. After diagnosing the problem (bad thermistor), I had to order the parts and was able to repair and reassemble the dryer several days later. After removing the drum, I cleaned all the dust etc. out of the inside (it gets dirty in there!) and inspected,... Read more

In 2012 I purchased an LG French door bottom freezer fridge. this thing was a problem from day one, I had to call 3 technicians where I bought it from- a nameless major retailer. through the 2 1/2 years I have had it, the problems were always with the ice cube maker, and finally, the motor finally stalled. I was able to revive it, but only for a short time- then I went to replace the unit all together and searched high and low until I came across Appliance Pros. I actually had no idea that 2 of... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

• Won't start
• No heat
• Little to no heat when broiling
• Oven not heating evenly

We were getting an intermittent F19 code on our lower oven mainly. This code gets triggered when the oven fails to heat up to a minimum temperature within a specific amount of time. I figured this was being caused by an ignition failure so I bought this new ignitor. As it turns out, if you have a double oven then you will have two ignitors. Just keep that in mind in case you are thinking about replacing both or you are seeing errors in both ovens. The ignitor in the lower oven is located below... Read more

I watched the video that was shown on this website to slide the top back, remove the control panel, remove the front panel of the washer, remove the old gasket (the two tension springs are easy to get off, not as easy to replace), cleaned out years of gunk and soap that had built up behind the gasket for 10 years as well as under the rollers in the drum (each roller has a screw, remove it, slide the roller assembly forward and lift up to take off the rollers, and the roller can be broken down... Read more

• Leaking
• Not dispensing water

I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more

• Won't start
• Lid or door won't close
• Door latch failure
• Will not agitate

Superfast parts delivery. Got packages by the second day. Videos were extremely helpful and well done; we couldn't have done without them although we came across slight differences in our machine and found workarounds. Our machine did not drain the water so I drained the water manually via drain tube at bottom of the machine and checked the filter for blockage. All clear so I read articles on the internet and watched videos and took a chance on replacing the drain pump and circulating motor... Read more

• Leaking

Removed the old line and replaced with the new. This is the sixth time I've replaced the line. Yes you read that right, the sixth time. Lines fail about every 6-8 months so I can change one out now in about 10-15 minutes. Bought the refrigerator in Feb '09 and the line first failed in March 2012. Since then I've had failures in as little as 4 months to as much as 9 months. Frustrating to say the least, but I'm a whiz at changing out the line :-) Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

• Lid or door won't close

This was a super-easy repair. You have to line up the spring so that it sits on the bumps inside the magnet holder and the door, then you have to line up the tabs on the magnet holder so they will slide into the slots on the door. Then you just push it in. Repair took less than a minute. Read more

We had a problem of lint building up inside of the filter slot. Once I took a long brush and cleaned the recess where the filter slides I was able to see that the old filter was not catching all the lint. Upon closer examination I noticed that the seal around the filter had become compressed. that's when I order another filter from AppliancePartsPros.com. My new filter came within three days and my dryer has been working fine ever since then. Read more

Searched the internet and found that the culprit could be 3 different parts. Ordered them and fixed the issue by replacing the thermostat! Read more