Switch

If your range burner won't spark or ignite when you turn the knob, this burner igniter switch restores spark delivery for reliable lighting.

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

This pressure switch monitors the water level inside the washer tub and signals the control board when the correct fill level has been reached. It connects to a small air hose that runs to the tub. Replace this switch if your washer overfills, underfills, does not fill at all, or fails to advance past the fill cycle.

This wiring harness routes power and signals between a refrigerator's control components and electrical devices, restoring reliable electrical connections for operation and controls. It replaces a damaged or broken harness to help regain normal appliance function. What it does:

• Connects control board, sensors, lights, and other electrical components to provide power and signal paths
• Replaces frayed, burnt, or damaged wiring that can cause intermittent or complete loss of function
• Helps resolve symptoms such as lights or dispenser not working, erratic controls, or failure of specific features tied to wiring
• Restores proper connector fit and secure electrical contacts when original harness pins or wires are compromised

• One wiring harness as shown

• Always disconnect power to the appliance before starting any repair
• Match connector shapes and wire colors to the original harness; route along original paths and secure with clips or ties
• Inspect mating connectors and control board terminals for damage before installing the new harness

The ignition switch is the part of lawn and garden equipment that features an ignition to turn on and off with a switch. These are common on lawn tractors, as well as some lawn mowers, wood chippers, tillers, and log splitters. While these switches tend to be robust, they may eventually wear out. Some might have a mechanical failure after being used for years. Others might have electrical issues. Regardless of the reason for the failure, they will need to be replaced to continue using the machine. This is a genuine OEM part that is sold individually. It is a complete kit, which will include not only the switch, but also a washer and nut to secure the switch into the housing, and two ignition keys. The ignition switch can work with lawn tractors from brands such as MTD, Ryobi, Troy-Bilt, Bolens, Yard Machines, and Craftsman.

Fix a refrigerator light that stays on or won't turn off when the door closes with a new door switch. Simple repair that restores proper door detection.

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

Fix a range hood that won't turn on or respond to controls with this rocker switch. Restores reliable on/off operation to your control panel. Direct fit.

Fix dishwasher buttons that won't respond or cycles that won't start with this push button switch. Direct replacement for worn control panel buttons.

This control component allows selection of different heat settings and is located on the dryer's control panel. Replace it if you can't select certain temperature settings, the dryer runs too hot or cold, or the switch feels loose or unresponsive.

This is an electrical relay used in the washer's motor or control circuit to switch power to specific components during operation. It helps regulate the timing and function of the wash and spin cycles. Replace this relay if the washer motor won't start, the machine hums but doesn't agitate or spin, or if cycles fail to advance properly.

This is a spark ignition switch used on gas ranges and cooktops to detect burner position and activate the igniter when the knob is turned. It sends a signal to the spark module to generate the electric spark that lights the gas burner. Replace this switch if a burner fails to spark when turned on, sparks continuously even after the flame is lit, or if the igniter clicks but won't stop.