General Electric Gasket & Seal

Replace your cooktop's control panel seal to prevent moisture and debris from entering the control area. Essential when seal shows wear or damage. Verify fit with your model number before ordering.

This glass and shaft seal assembly replaces a damaged oven door glass seal and the shaft seal that helps keep heat and moisture contained. Restores proper sealing to improve oven performance and reduce heat loss. What it does:

• Seals the gap around the oven door glass and shaft to help contain heat and cooking vapors
• Reduces heat transfer and prevents excess moisture buildup near the door area
• Helps maintain consistent oven temperatures by restoring a proper seal
• Commonly replaced when you see visible wear, cracked/brittle seal, or heat leaking from the door edge

• One glass and shaft seal assembly as shown

• Disconnect power to the appliance before beginning any repair
• Handle glass components carefully to avoid breakage or injury; wear work gloves and eye protection
• Basic hand tools are typically required; follow the appliance service manual for disassembly/reassembly steps

This door gasket is the flexible sealing strip that mounts around a refrigerator door to keep cold air in and warm air out, helping maintain temperature and reduce energy use. It restores a tight door seal for proper cooling performance. What it does:

• Seals the door edge to prevent warm air infiltration and cold air loss
• Helps reduce frost buildup and prevents moisture leaks into the compartment
• Supports consistent internal temperature to protect food freshness
• Common symptoms of a failing gasket: visible gaps, torn or flattened seal, cold/temperature fluctuations, excess frost or condensation

• High-level: remove the old gasket, align and seat the new gasket into the channel around the door; some models use screws or retainers
• Safety-first: unplug the appliance or disconnect power before attempting removal/installation
• Handle carefully to avoid tearing; warm the gasket slightly to help fitment if needed
• Refer to your model's service manual or OEM instructions for model-specific steps and fastener locations

This rubber agitator cap seal creates a watertight barrier at the base of the washer agitator to help prevent leaks and keep the transmission area dry. It's a simple replacement that restores proper sealing around the agitator. What it does:

• Seals the agitator base to reduce water entering the transmission and cabinet area
• Helps prevent leaks that can cause rust, puddling, or damage under the washer
• Keeps contaminants and detergent residue out of the gearcase area
• Supports consistent wash performance by maintaining a dry drive assembly

• Disconnect power and turn off the water supply before starting any repair
• Remove the agitator cap and agitator per your model's service instructions to access the seal
• Inspect surrounding parts (agitator cap, agitator, and shaft) for wear and clean mating surfaces before installing the new seal

This boot auger motor drives the auger inside the ice dispenser boot to move ice from the bin to the dispenser chute. Replaces a failed motor to restore normal ice dispensing and reduce jams. What it does:

• Rotates the auger inside the dispenser boot to push ice forward for dispensing
• Helps prevent ice buildup by moving packed cubes during dispense cycles
• Stops working when motor windings or gears fail, causing no ice to dispense or intermittent dispensing
• Works with the dispenser drive and auger assembly to transfer ice from the bin to the chute

• One boot auger motor

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the freezer/refrigerator door trim and dispenser housing; follow OEM service instructions
• Inspect related components (auger, coupler, wiring) and replace if damaged

Replace your refrigerator's chill drawer gasket to restore a tight seal and maintain proper temperature. Fixes worn or compressed seals causing moisture issues.

Seals the vertical door mullion area to keep cold air in and reduce condensation. Replace when worn or damaged to restore proper sealing. Confirm fit.

Seals the chill compartment to maintain proper temperature and prevent frost buildup. Replace if worn, torn, or hardened. Confirm fit with your model.

Refrigerator plenum gasket seals air duct between fresh food and freezer sections. Replace if torn, cracked, or causing temperature issues. Verify fit with your model number before ordering.

Replace your refrigerator plenum gasket to restore proper airflow and temperature control. Install when torn, compressed, or causing air leaks. Verify fit with your model number.

Replace worn felt pads that cushion your range door and prevent rattling or gaps. Essential when door closes unevenly or makes noise. Confirm fit with model.

Seals the cooktop to your range, preventing spills from entering the burner area. Replace if cracked, worn, or leaking. Verify fit with your model number.

Cooktop control seal prevents moisture and debris from entering the control panel. Replace if cracked, worn, or loose to maintain a proper seal. Confirm fit with your model number before ordering.

Replace your cooktop control panel seal to prevent moisture and debris from entering the control area. Essential when seal shows wear or damage. Verify fit with your model number before ordering.

Insulation foam tape seals the gap between your cooktop and countertop, preventing debris from falling into the burner box. Replace if worn or damaged.

Replace your range door gasket to restore proper sealing and heat retention. Install when you notice heat escaping or visible wear. Verify fit with your model.