General Electric Gasket & Seal

This damper gasket seals the refrigerator air damper opening between the freezer and fresh food compartments to prevent air leaks and help maintain stable temperatures. A new seal supports proper airflow and helps reduce moisture or frost near the damper. What it does:

• Seals the perimeter of the air damper/baffle to prevent bypass air leaks
• Helps regulate airflow from freezer to refrigerator for consistent cooling
• Wear, flattening, or tears can lead to warm spots in the fresh food section
• May also contribute to condensation, frost, or whistling/draft at the damper cover

• 1 damper gasket

• Unplug the refrigerator before servicing
• Remove the interior damper cover/grille to access the damper; note gasket orientation
• Seat the new gasket evenly around the damper frame without stretching or twisting
• Reinstall cover, restore power, and verify airflow and door sealing

This suction ring sits in the dishwasher's sump/filter area and helps channel wash water into the circulation system. Replacing a worn ring can help restore proper water pickup and spray pressure for reliable cleaning performance.

• Helps maintain suction at the pump inlet for steady water flow to the wash system
• Supports proper spray arm rotation and wash coverage
• Common symptoms of failure: poor cleaning, weak spray, spray arms not turning consistently, or unusual noise from the sump area
• Wear or damage can disrupt circulation

• Disconnect power and water supply before servicing
• Remove the lower rack, then the lower spray arm and filter/sump cover to access the ring
• Note the ring's orientation; press the new ring fully into place before reassembly
• Run a short test cycle to ensure proper circulation

This oven door gasket restores a tight seal between the door and oven cavity, helping the oven heat efficiently and bake evenly. Replace a worn or damaged seal to stop heat loss and temperature swings.

• Seals the gap between the oven door and front frame to retain heat and maintain set temperature
• Can help resolve heat escaping around the door and uneven or extended bake times
• Common failure signs: tears, fraying, brittleness, or permanent flattening of the gasket
• Supports consistent preheat and recovery performance

• Disconnect power or shut off gas and allow the oven to cool completely
• Open the door and remove the old gasket from its retaining holes or channel; clean the area
• Align the new gasket and press the retainer ends into the mounting holes evenly—do not stretch the seal
• Close the door to check fit; a short preheat can help the new gasket seat

This oven door gasket assembly seals the door to the oven frame to keep heat in and prevent hot air leaks. Replacing a worn seal restores proper preheat times, temperature stability, and more consistent baking performance.

• Forms a heat-resistant seal between the oven door and front frame
• Helps reduce heat loss and maintain set oven temperatures
• Common fix for heat leaking around the door, long preheat times, and uneven baking/roasting
• Replace if the gasket is torn, frayed, flattened, brittle, or missing retainer ends

• Disconnect power at the breaker and allow the oven to cool completely
• Open the door and remove the old gasket from its retainers; note clip/hook locations and orientation
• Clean the sealing surface/channel before installing
• Install the new gasket without stretching; fully seat all retainers and verify the door closes evenly

Green bearing slide that replaces a worn bearing guide in select GE laundry appliances, helping restore smoother drum movement and reduce vibration and noise from a misaligned bearing assembly. Fits where the bearing rides or is guided. What it does:

• Guides the bearing assembly for steadier drum rotation — symptoms include grinding, squeaking, or rough spin cycles.
• Helps correct minor drum wobble and imbalance caused by a worn guide surface.
• Protects the bearing mating surface from accelerated wear by maintaining alignment.
• Can improve spin stability and reduce abnormal vibration when the guide is failing.

• Disconnect power and water supply before beginning any repair.
• Part typically accessed by removing the washer front panel or tub components.
• Verify the part number and color match your machine before installing.

This QC seal damper is the refrigerator air damper that helps control and seal airflow between compartments to keep temperatures stable and reduce energy loss. Replacing a worn damper restores proper airflow regulation. What it does:

• Regulates cold air flow from the freezer to the fresh-food section to help maintain set temperatures.
• Seals the transfer opening to prevent unwanted air exchange and reduce temperature swings.
• A faulty or stuck damper can cause uneven temperatures, excessive frost/ice, or poor cooling in the refrigerator compartment.
• Dampers can produce rattling or buzzing noises when damaged or obstructed.

• Always disconnect power to the appliance before servicing.
• Access may require removing interior shelves, drawers, or a panel; handle inner liners and gaskets carefully.
• Inspect surrounding seals and mounting points; ensure the damper is oriented correctly and moves freely before reassembling.
• After installation, restore power and verify proper operation and temperature stabilization.

This gasket seals the oven's convection fan assembly. By closing the gap between the fan cover and the oven cavity, it helps prevent air leaks and supports proper airflow for more even convection cooking and steadier temperatures. What it does:

• Seals the junction between the convection fan cover/housing and the oven liner
• Helps maintain correct airflow during convection operation
• Supports more consistent oven temperatures and even baking
• Replace if the seal is torn, frayed, compressed, or missing

• 1 convection fan gasket

• Disconnect power and allow the oven to cool completely before servicing
• Access by removing the interior convection fan cover; note gasket orientation
• Clean mating surfaces before installing; seat gasket evenly and reassemble
• Use care around sharp edges; wear cut-resistant gloves and eye protection

This replacement oven door gasket forms the heat-resistant perimeter seal around the door opening. Restores a tight seal to retain heat, support accurate temperatures, and reduce warm-air leakage for better baking performance.

• Creates the compressible seal between the oven cavity and door to keep heat in
• Helps the oven preheat efficiently and maintain even temperatures
• Reduces warm air and odors escaping around the door edge
• Common failure signs include fraying, flattening, gaps, longer preheat, or uneven baking

• Disconnect power and allow the oven to cool completely; wear gloves
• Open the door and remove the old gasket from its retainers/channels, noting clip locations and orientation
• Clean the groove/retainer; starting at the top center, press the new gasket in evenly without stretching and seat corners fully
• Close the door and check for uniform contact around the perimeter

Fits GE/Hotpoint washers.

This replacement gasket seals the evaporator cover to the cabinet, preventing air leaks and directing airflow where it belongs. Restores a tight seal to help minimize frost buildup and temperature swings for more consistent cooling performance.

• Seals the perimeter of the evaporator cover to prevent air bypass and warm-air infiltration
• Helps maintain proper airflow through the evaporator and air ducts
• Can reduce frost/ice on or around the rear panel and air outlets
• Improve and stabilize refrigerator/freezer temperatures when the original gasket is torn, compressed, or missing

• Disconnect power to the refrigerator and wear cut-resistant gloves
• Remove shelves/bins and the evaporator cover; retain screws/clips
• Remove the old gasket and clean mating surfaces; seat the new gasket evenly without gaps or twists
• Reinstall the cover and restore power and verify no air leaks

This oven door gasket creates a heat-tight seal between the oven door and frame to help retain heat and improve cooking consistency. Replacing a worn gasket reduces heat loss and limits smoke or steam escaping during use. What it does:

• Seals the oven door to help maintain internal temperatures and consistent cooking results.
• Reduces heat and steam leakage that can cause longer cook times or uneven baking.
• Typical signs you need it: visible gaps, flattened or torn seal, or heat/steam escaping from the door.
• Matches OEM fitting style for a direct replace of the damaged or degraded seal.

• Disconnect power to the oven and allow it to cool completely before starting.
• Access the gasket per the manufacturer's guidance—some doors may need to be opened or removed for easier access.
• Remove the old gasket from the channel, then press the new gasket evenly into the channel so it seats fully around the door perimeter.
• Reuse original retainers or hardware; if adhesive or clips are required, follow the oven maker's instructions.

This seal for the front frame creates a tight barrier between the oven door and frame to help retain heat and reduce smoke or odor escape. It restores a proper door seal to improve cooking performance and safety. What it does:

• Replaces worn, torn, or deformed front-frame gasket that allows heat or smoke to leak from the oven cavity
• Helps maintain consistent oven temperatures for more even cooking and baking
• Reduces heat transfer to surrounding cabinetry and surface areas
• Stops drafts, burning odors, or visible gaps around the door edge

• One seal for the front frame

• Disconnect power and let the appliance fully cool before attempting service
• Inspect orientation and seating before final installation; some models require door removal for access
• Use proper tools and gloves to avoid cuts; ensure seal is fully seated and continuous around the frame

The TUB SEAL is an OEM component specifically designed for GE washers. It is a rubber gasket located between the inner and outer wash tubs designed to prevent leaks. During cycles, the seal withstands contact with fast spinning and surging water pressure to maintain a watertight barrier. 

Symptoms of a bad tub seal include: 

• Puddles, drips, or leaks visible beneath the unit during or after cycles
• Excess moisture trapped between the inner and outer tubs
• Mineral or soap film buildup indicating escaping water 

Causes can be cracks developing from age and repetitive flexing during cycles, or deformities in the rubber preventing proper compression.

Replace yours today with this genuine OEM GE part to ensure a dependable water containment solution. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.

This replacement freezer door gasket restores a tight seal to help keep the freezer cold and reduce frost buildup. Designed to fit the freezer door, it gives an easy, low-cost way to improve cooling performance and efficiency. What it does:

• Seals the freezer door to prevent warm air and moisture from entering
• Helps reduce frost buildup and maintains consistent internal temperature
• Restores proper door closure when the existing gasket is cracked, flattened, or torn
• Supports energy efficiency by minimizing cold-air loss

• Inspect door frame and mounting channel; clean and dry before installing the new gasket
• Press gasket into the door channel evenly, starting at one corner and working around the perimeter
• For best seal, level and align the door after installation; allow gasket to seat for several hours
• Disconnect power only if needed for light removal tasks

This door gasket is the flexible rubber seal that mounts around the refrigerator door to maintain an airtight seal, helping preserve internal temperatures and reduce energy loss from leaks. What it does:

• Seals the gap between the refrigerator door and cabinet to keep cold air inside.
• Prevents moisture intrusion, reducing frost, condensation, and excessive compressor run time.
• Restores proper door contact when original gasket is cracked, torn, warped, or no longer seals.
• Common symptoms: visible gaps, light showing around closed door, frost buildup, or higher-than-normal interior temperatures.

• Disconnect power to the appliance before beginning any work.
• Remove the old gasket and clean the door channel; inspect the mounting surface for damage.
• Press the new gasket into the channel starting at the corners, working around the door for an even fit; warm the gasket slightly (hair dryer on low) if needed to help seat it.
• Avoid sharp tools that can tear the gasket.

This inside gasket clamp secures the appliance's inner door gasket, helping maintain a tight seal and reduce leaks. It's a small but important retaining clip used where the gasket meets the door or opening. What it does:

• Holds the inner edge of the door or tub gasket in place to keep the seal seated
• Helps prevent water or air from leaking around the door during operation
• Restores proper gasket alignment when a worn or broken clamp allows the gasket to shift
• Works as a replacement for damaged or missing gasket retaining clamps

• One gasket inside clamp (single clamp as shipped)

• Recommended to inspect the gasket and surrounding trim for wear before installing the clamp
• Remove power and water (if applicable) to the appliance before servicing
• May require basic hand tools and careful prying to remove the old clamp and seat the new one
• If gasket is damaged or torn, replace the gasket as well for a reliable seal