General Electric Gasket & Seal

Black

Replacement refrigerator door gasket that restores a tight seal to help maintain proper cooling and reduce frost and moisture buildup. Fits the door channel to stop warm-air leaks and improve overall temperature stability. What it does:

• Seals the refrigerator door perimeter to keep cold air in and warm air out.
• Helps reduce frost and ice buildup inside the compartment.
• Can reduce condensation and uneven cooling caused by a worn or damaged seal.
• Common symptoms of a failing gasket: warm spots, excess frost, visible gaps around the door, or higher-than-normal energy use.

• Unplug the appliance and remove food from the door area before beginning work.
• Clean and dry the gasket channel and door surface; align the gasket and press it fully into the channel for an even seal.
• If the gasket is stiff, gently warming it can make installation easier—avoid excessive heat.
• Confirm this part number matches your appliance model before installing.

This front vegetable pan glass seal replaces the worn or damaged gasket that fits along the glass front of a refrigerator crisper/vegetable drawer. Restores a snug fit to help reduce drafts, rattling and food falling beneath the drawer. What it does:

• Seals the front edge of the crisper/vegetable drawer glass to help maintain proper airflow and keep produce fresher.
• Holds the glass front securely to reduce rattling, slipping or gaps.
• Prevents small food items and debris from slipping under the pan.
• Common symptoms: torn, brittle or missing seal; visible gap at the drawer front; rattling or debris collecting beneath the drawer.

• Remove food and slide out the crisper/vegetable drawer to access the glass front before replacing the seal.
• Remove the old seal and clean the channel of any debris or adhesive; press the new seal firmly into the channel until fully seated.
• Wear gloves and use caution around glass edges to avoid cuts; no special tools are usually required.
• If clips or adhesive are present, inspect and reuse or replace them as needed; replace cracked or damaged glass rather than relying on the seal.

Evaporator cover gasket creates a moisture- and air-sealing barrier between the evaporator cover and freezer liner to help reduce frost buildup and improve cooling consistency. Replacing a worn gasket helps prevent ice accumulation and water leaks. What it does:

• Seals the evaporator cover to minimize moisture intrusion and air leakage into the evaporator area.
• Helps reduce frost and ice buildup on the evaporator and freezer walls.
• Can help address symptoms such as excess frost, water pooling in the freezer, or uneven/freezer temperatures.
• Restores proper evaporator cover fit for more consistent defrost performance.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the evaporator cover per your model's service instructions, remove the old gasket, and clean the mating surfaces before installing the new gasket.
• Seat the gasket fully around the cover; some models use clips or adhesive.
• After reassembly and power-up, monitor the freezer for proper sealing, frost control, and any signs of leaks.

This replacement door gasket seals a French-door refrigerator compartment to help maintain proper temperature and reduce energy loss. Restores the door seal to prevent warm air infiltration and condensation buildup. What it does:

• Creates an airtight seal around the refrigerator door to keep cold air in and warm air out
• Helps prevent frost and ice buildup by reducing moisture entry
• Reduces energy use caused by a leaking or damaged seal
• Common symptoms: persistent condensation, warm spots near the door, visible gaps, or a seal that looks cracked or deformed

• Unplug the refrigerator or disconnect power before beginning work
• Clean the gasket channel and mating surface thoroughly before installing the new gasket
• Align the gasket into the channel and press evenly around the perimeter so it seats fully
• After installation, allow the gasket to form to the door; check for consistent contact and adjust as needed

This foam tape seals and cushions the oven door assembly to reduce vibration and help keep the door glass and inner components stable. It restores proper spacing and helps reduce rattling or light air leaks around the door. What it does:

• Provides a soft, compressible seal between the door and frame to reduce noise and movement
• Cushions and protects glass and trim from contact and vibration
• Helps limit minor air leakage that can allow heat or odors to escape
• Commonly used when door trim or glass is loose, rattling, or shows visible gaps

• One adhesive-backed foam tape strip

• Clean and dry mating surfaces before applying to ensure good adhesive contact
• Measure and trim to fit; press firmly along the full length for proper adhesion
• Replace only with the same style of tape—do not use electrical or non-heat-rated foam in high-temperature areas
• Disconnect power/cool the appliance before working on the door assembly to avoid burns or injury

This seal cap fits the washer tower to help seal the upper tower area and keep water contained during operation. It prevents leaks and helps maintain proper washer function at the tower interface. What it does:

• Provides a watertight seal where the upper tower meets the tub/tower assembly
• Helps stop leaks and moisture migration around the tower area
• Supports normal water flow and prevents damage from seepage
• Commonly replaced when the tower area shows signs of dampness or visible wear

• One seal cap (upper tower)

• Designed for direct replacement;
• Turn off power and water supply before beginning any repairs
• Inspect surrounding seals and tower components for wear during replacement

This control seal sits in the control area of your range or cooktop. It creates a barrier that helps keep spills, grease, and debris out of the manifold/console for smoother control operation and longer component life.

• Seals the gap around control openings to block spill intrusion
• Helps protect internal valves/switches from moisture and debris
• Aids reliable knob/control function after cleanups and spills
• Common signs it's needed: cracked, deformed, or missing seal; liquids passing through control openings; gritty or sticky knob feel

• Disconnect power; also shut off gas. Allow the appliance to cool.
• Pull the control knob straight off and remove the old seal.
• Clean and dry the mating surface; seat the new seal evenly and flat.
• Reinstall the knob and verify the control turns freely with the seal fully seated.

This glass and shaft seal assembly replaces a damaged oven door glass seal and the shaft seal that helps keep heat and moisture contained. Restores proper sealing to improve oven performance and reduce heat loss. What it does:

• Seals the gap around the oven door glass and shaft to help contain heat and cooking vapors
• Reduces heat transfer and prevents excess moisture buildup near the door area
• Helps maintain consistent oven temperatures by restoring a proper seal
• Commonly replaced when you see visible wear, cracked/brittle seal, or heat leaking from the door edge

• One glass and shaft seal assembly as shown

• Disconnect power to the appliance before beginning any repair
• Handle glass components carefully to avoid breakage or injury; wear work gloves and eye protection
• Basic hand tools are typically required; follow the appliance service manual for disassembly/reassembly steps

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn, torn, or deformed seal to restore a tight door closure. What it does:

• Creates an airtight seal around the refrigerator door edge to preserve internal temperature.
• Helps prevent frost buildup and condensation by stopping warm, moist air from entering.
• Reduces compressor run time and energy waste caused by a leaking door.
• Restores proper door alignment and magnetic closure when the original gasket is damaged.

• One replacement refrigerator door gasket

• Disconnect power to the appliance before starting any work.
• Clean and dry the door flange thoroughly before fitting the new gasket.
• Start at one corner, press gasket firmly into the channel, and ensure magnetic/retention edges seat evenly around the door.
• If gasket wrinkles or does not seat, warm it slightly or allow time for it to relax; avoid sharp tools that can damage the new seal.

This boot auger motor drives the auger inside the ice dispenser boot to move ice from the bin to the dispenser chute. Replaces a failed motor to restore normal ice dispensing and reduce jams. What it does:

• Rotates the auger inside the dispenser boot to push ice forward for dispensing
• Helps prevent ice buildup by moving packed cubes during dispense cycles
• Stops working when motor windings or gears fail, causing no ice to dispense or intermittent dispensing
• Works with the dispenser drive and auger assembly to transfer ice from the bin to the chute

• One boot auger motor

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the freezer/refrigerator door trim and dispenser housing; follow OEM service instructions
• Inspect related components (auger, coupler, wiring) and replace if damaged

This small cooktop gasket seals and cushions the edge of a stovetop glass or ceramic surface to help keep out spills and debris and reduce vibration. It restores a proper seal around the cooktop for safer, cleaner operation. What it does:

• Provides a protective seal between the cooktop and surrounding trim or countertop
• Cushions the cooktop edge to reduce glass-to-frame contact and rattling
• Helps prevent food, liquid and debris from entering gaps under the cooktop
• Can reduce moisture-related issues around the cooktop perimeter

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the cooktop or trim to access the gasket channel
• Clean and dry the mounting surface before installing the new gasket for best fit
• Press the gasket into place evenly; replace any retaining clips or hardware removed during disassembly

This ice maker seal kit replaces worn or damaged gaskets that help seal and stabilize the ice maker assembly for reliable operation and to reduce leaks. Use it to restore a tight ice-maker-to-freezer fit. What it does:

• Replaces seals/gaskets that prevent water leaks around the ice maker
• Helps maintain proper ice maker alignment and operation
• Supports consistent ice production by ensuring proper water flow control

• Disconnect power and turn off the water supply before servicing
• Remove the ice maker assembly to access and replace seals as needed
• Use common hand tools; avoid over-tightening fasteners that can deform seals
• Inspect surrounding mounting surfaces for damage, clean before installing new seals

This adhesive-backed foam tape provides cushioning and helps seal small gaps around appliance panels and components to reduce vibration and prevent dirt intrusion. It's a simple maintenance piece that restores proper spacing and fit. What it does:

• Cushions panels and components to reduce rattling and noise
• Helps seal small gaps to limit dust and debris entry
• Protects surfaces from abrasion where parts contact one another
• Adheres to clean, dry surfaces for a secure fit

• Clean and dry the mounting surfaces before applying for best adhesion
• Press firmly along the tape length to ensure full contact
• Trim to fit with scissors or a utility knife; avoid stretching the tape while applying
• Remove old foam gently to avoid damaging surrounding finishes

This oven felt seal fits around the door perimeter to cushion the door and help reduce heat loss. It restores the intended door clearance and soft contact between the oven door and frame for safer, quieter operation. What it does:

• Cushions the oven door edge to prevent metal-on-metal contact and reduce rattling
• Helps limit heat and smoke from escaping the oven cavity when the door closes
• Restores proper door clearance to prevent scraping or uneven sealing
• Commonly replaced when felt is worn, compressed, torn, or missing

• One oven felt seal as shown

• High-level replacement; remove the oven door or open hinge per your service manual before replacing the seal
• Work with the oven powered off and fully cooled; disconnect power for safety
• Press the felt into the channel or adhesive area; ensure even fit around the full perimeter