General Electric Gasket & Seal

This door gasket seal replaces a worn or damaged refrigerator or freezer door seal to restore a tight closure and help maintain proper temperature. It helps stop air leaks that can cause frost build-up and higher energy use. What it does:

• Forms a replacement seal around the appliance door to maintain an airtight closure
• Helps reduce interior temperature fluctuations that can lead to frost or spoiled food
• Restores proper door alignment and sealing where old gasket is cracked, torn, or compressed
• Commonly used when you see visible gaps, drafts, or persistent moisture at the door edge

• Designed for a direct OEM-fit; inspect the door channel and mounting surface before installing
• Clean the gasket channel and door edge to remove debris for best sealing contact
• Warm the gasket slightly (per OEM guidance) if needed for easier fitting; avoid open flames

Replace your air conditioner gasket seal to prevent air leaks and maintain cooling efficiency. Install when worn or damaged. Verify fit with your model.

Seals the chilled compartment to maintain proper temperature and prevent warm air leaks. Replace if torn, cracked, or no longer sealing tightly.

Seals your refrigerator's vegetable pan frame to maintain proper humidity and temperature. Replace if torn, cracked, or moisture escapes. Verify fit.

Seals freezer door to maintain temperature and prevent frost buildup. Replace if torn, cracked, or door doesn't seal properly. Verify fit with model number.

A foam insulation barrier that helps seal and protect refrigerator cabinet cavities from air and moisture intrusion. Replaces worn or damaged foam to support proper airflow and reduce the risk of frost buildup around internal components. What it does:

• Provides an insulating seal between cabinet panels and service openings
• Helps limit warm air ingress that can cause frost or reduced cooling performance
• Cushions and isolates components to reduce vibration noise
• Restores original fit where foam has deteriorated or been removed during repairs

• Disconnect power to the appliance before starting any repair
• Remove surrounding panels as needed to access the foam location
• Clean and dry mounting surfaces before applying; use adhesive if required by OEM instructions
• Avoid compressing or blocking vents and airflow paths during installation

Motor seal for air conditioners. Replace if you notice air leaks, reduced cooling efficiency, or moisture around the motor. Verify fit with your model number.

This Form Gasket 2 is a replacement sealing gasket designed to restore a tight, reliable seal where the original foam/form gasket has become compressed or damaged. Replacing it helps reduce leaks and maintain normal appliance operation. What it does:

• Replaces a worn or damaged foam/form gasket to restore proper sealing
• Helps prevent water, air, or debris from passing where the original gasket seals
• Commonly used where a formed seal cushions or closes a gap in the appliance assembly
• Address symptoms such as visible gaps, leaks, rattling, or improper sealing along the joint

• One Form Gasket 2 as shown

• Install in clean, dry area; remove old gasket and clean mating surfaces before fitting the new gasket
• Fit gasket to the formed channel or mounting surface per the appliance's service instructions
• Wear gloves to protect hands from sharp edges and to avoid contaminating the gasket surface

This self-adhesive foam strip seals gaps and cushions components to reduce drafts, noise, and moisture intrusion—helpful for restoring proper airflow and improving efficiency where foam padding or gap sealing has deteriorated. What it does:

• Provides a soft seal to close small gaps and prevent air leaks
• Cushions panels to reduce vibration and rattling noises
• Helps limit moisture and dust entry around seals and components
• Supports consistent temperature by reducing unwanted airflow

• Clean and dry the mounting surface before applying for best adhesion.
• Trim to length with scissors or a utility knife; press firmly to set adhesive.
• Avoid stretching the foam while applying; allow adhesive to set 24 hours for full bond.
• If near electrical components, disconnect power before working and avoid covering vents.

Refrigerator door foam tape seals gaps and reduces noise between door components. Replace if worn, compressed, or causing air leaks. Verify fit with your model.

A replacement damper gasket that seals the refrigerator air/damper assembly to help maintain proper airflow and temperature control inside the fresh-food compartment. Restores the damper seal to reduce drafts and energy loss. What it does:

• Creates an airtight seal around the air damper to keep conditioned air inside the compartment
• Helps the damper regulate airflow for more consistent temperatures
• Can reduce frost buildup and limit warm-air leaks that cause the compressor to run more
• Common symptom: uneven temperatures or a draft near the damper area

• One damper gasket

• Disconnect power to the appliance before beginning any service
• Remove the damper housing or inner liner trim as needed to access the gasket; handle plastic parts gently to avoid cracking
• Seat the gasket fully in the damper groove and reassemble components in reverse order

This refrigerator pan/vegetable frame gasket seals the crisper area to help maintain proper humidity and keep produce fresher. It replaces a torn, loose, or hardened gasket to restore the drawer seal. What it does:

• Seals the crisper/pan opening to help retain humidity for stored fruits and vegetables
• Helps prevent cold air loss and reduces temperature fluctuation in the drawer area
• Commonly replaced when the gasket is cracked, warped, flattened, or detached
• Fits around the vegetable/crisper pan frame to restore an effective seal

• Disconnect power or unplug the appliance before starting work
• Remove crisper drawer/pan to access the gasket area
• Press the gasket into the channel around the pan/frame; avoid overstretching
• Do not use sharp tools that could nick the gasket or surrounding trim

Seals the bottom center of your dishwasher door to prevent leaks during wash cycles. Replace if water leaks from the door bottom. Verify fit by model.

Door gasket and label assembly creates an airtight seal to keep cold air in and moisture out. Replace when worn or damaged to restore efficiency. Verify fit.

Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.