General Electric Motor

This motor assembly kit replaces a worn or failed motor to restore proper mechanical drive and motion in the appliance. It's a direct-fit replacement designed to match the original assembly's form and function. What it does:

• Replaces the appliance's motor assembly to restore spinning, stirring, or drive motion
• Stops symptoms like no movement, intermittent operation, or unusual humming from the motor area
• Restores correct mechanical linkage between the motor and driven components
• Matches OEM fit and mounting points to simplify replacement

• One motor assembly kit (single complete motor assembly)

• Turn off power to the appliance at the breaker or unplug before beginning any repair
• Follow OEM disassembly steps to access the motor area; keep fasteners and small parts organized
• Handle electrical connectors carefully; wiring matches diagrams before re-energizing

This fan motor powers the fan blade or blower wheel to move air through the unit. Replacing a worn or seized motor restores airflow and heat transfer, helping the system maintain proper temperatures and operate reliably.

• Rotates the fan to circulate air across coils and components
• Supports correct cooling performance and helps prevent overheating
• Reduces noise and vibration caused by a failing motor
• Typical symptoms: fan not running, weak airflow, loud humming/squealing, intermittent operation, or a burning odor

• Disconnect power before servicing and allow components to cool
• Note and label all wire connections; take a photo for reference
• If a start/run capacitor is present, discharge it safely before handling
• Wear cut-resistant gloves; transfer any brackets or grommets from the old motor as required and verify free blade rotation after install

Condenser fan assembly moves air across the condenser to help dissipate heat so the refrigerator cools efficiently. Replacing a failing condenser fan can reduce noise and prevent the compressor from working overtime. What it does:

• Circulates air over condenser coils to remove heat produced during cooling
• Helps maintain proper compressor operating temperature and system efficiency
• Stops or reduces loud buzzing, grinding, or rattling noises when the fan motor fails
• Addresses symptoms like frequent compressor cycling, poor cooling, or warm interior

• Always disconnect power to the appliance before accessing the condenser area
• Access is typically at the rear lower panel; remove panels carefully to reach the assembly
• Note fan blade orientation and wiring before removing; reconnect wires to the same terminals

This replacement auger motor drives the dispenser auger to move ice from the freezer bin to the dispenser chute, restoring reliable ice delivery. Fits dispenser assemblies that use the WR60X10276 auger motor. What it does:

• Turns the auger shaft to push ice through the dispenser chute for user-activated dispensing
• Replaces a motor that hums, fails to turn, or stops feeding ice
• Helps stop intermittent or no-ice-dispense symptoms when the auger motor is the faulty component
• Works as the mechanical drive for auger-style ice dispensers in compatible refrigerators

• One auger motor (WR60X10276)

• Disconnect power to the appliance before starting any repair
• Remove the freezer door liner or dispenser housing to access the motor and auger assembly
• Note wiring locations and mounting orientation during removal; reconnect wiring and secure mounting when installing
• Test dispenser operation with power restored and handle ice bin components carefully to avoid damage

Tangential blower that moves air through the oven's ventilation and control areas to help keep components cool and vent heat. Replacing a failed blower restores airflow for quieter operation and more consistent cooling around electronics. What it does:

• Circulates air across the oven vent and control area to dissipate heat; symptoms of failure include little or no airflow.
• Helps cool control electronics and nearby components; failure can cause high temperatures or thermal-related shutdowns.
• Reduces noisy or rough fan operation when bearings or motor wear.
• Supports proper venting after use to help the appliance cool down safely.

• Disconnect power to the appliance before accessing or replacing the blower.
• Allow the appliance to cool fully; remove access panels to reach the blower.
• Handle the blower and connector gently to avoid damaging the motor shaft or wiring; ensure correct orientation when reinstalling.

A blower assembly that circulates oven or range heat to support convection cooking. Replacing a worn or failed blower restores airflow for more even cooking and reduces noisy or grinding fan operation. Sold individually. What it does:

• Circulates hot air across the oven cavity to support convection and temperature consistency.
• Restores airflow that helps prevent uneven cooking or extended bake times when the blower fails.
• Common symptoms of failure: loud or grinding noise, little or no airflow from the convection fan, or reduced baking performance.
• Replaces assemblies that are worn, seized, or producing excessive vibration.

• Disconnect electrical power (and gas supply, if applicable) before starting any service.
• Allow the appliance to fully cool; remove access panels to reach the blower.
• Handle fan blades carefully to avoid damage; verify the blower spins freely and wiring connectors are secure before reassembly.

This blower assembly circulates air through the appliance to maintain proper airflow and ventilation. Replacing a worn or damaged assembly restores efficient exhausting and reduces unusual noises or poor airflow. What it does:

• Moves air through the appliance for proper ventilation and drying/performance
• Helps expel humidity, lint, and combustion byproducts
• Can resolve reduced airflow, weak performance, or excessive noise from the blower area
• Supports consistent temperature and cycle performance by maintaining airflow

• 1 blower assembly

• Disconnect power (and gas if applicable) before starting any repair
• Handle the blower carefully; edges and mounting tabs can be sharp
• Secure all mounting screws and duct connections
• Check lint traps and ducts for blockages when replacing the blower

This motor inverter is the electronic drive assembly that controls motor speed and torque, restoring proper motor operation and drive control for compatible appliances. It replaces the inverter electronics that govern motor performance. What it does:

• Regulates motor speed and direction to enable normal appliance drive functions
• Helps resolve intermittent motor operation, failure to start, or loss of drive control
• Restores electronic control of motor torque for cycles that require variable speed
• Clears symptoms related to erratic motor performance or inverter-related error codes

• Disconnect power to the appliance before starting any repair
• Handle the assembly carefully; avoid ESD (electrostatic discharge) to electronic components
• Install with matching part number; secure all connectors and mounting points

The Convection Motor is an OEM part compatible with GE wall ovens and convection ranges. As the primary component driving air circulation inside the oven cavity, it is responsible for the convection baking and roasting functions.

By circulating warm air around the food at high speed, the convection motor allows for faster and more even cooking without compromising quality. Causes of failure can include excess dirt or debris obstructing the motor shaft or blades, damage to motor wiring from heat, or normal component wear over time.  

Symptoms of a bad convection motor include:

• Convection cooking mode not working at all  
• Much longer than normal cooking times
• Unevenly cooked food despite rotation
• Loud grinding or whirring noises from inside the oven

This GE OEM replacement motor restores efficient convection performance. It is also compatible with Hotpoint, RCA, and select Kenmore ovens. Replace yours today for reliable cooking power.
 

This blower assembly circulates air through the appliance to support drying and venting, restoring proper airflow for consistent performance. It replaces a worn or damaged fan wheel and housing to reduce overheating and poor drying. What it does:

• Moves air through the appliance to aid drying and ventilation
• Restores airflow lost from cracked, warped, or broken blower wheel
• Helps eliminate overheating, long-dry times, or reduced airflow
• Works with the motor and ducting to maintain proper exhaust flow

• One blower assembly

• Disconnect power before servicing to avoid shock or injury
• Inspect motor shaft and mounting before installing; replace any damaged hardware
• Ensure blower is oriented and secured per manufacturer alignment to prevent noise or imbalance
• Verify clear, unrestricted ducting after installation for proper performance

This tangential blower moves air across oven/microwave components to cool electronics and vent heat. Replacing a worn blower restores proper airflow to help prevent overheating and reduce fan noise. What it does:

• Circulates air across internal components to maintain safe operating temperatures
• Helps cool control electronics and magnetron assemblies in ovens/microwaves
• Can cause overheating, reduced cooling, or unusual fan noise when failing
• Restores designed airflow when the motor or fan blades are worn or damaged

• Disconnect power to the appliance before beginning any repair
• Handle sharp sheet metal and internal components with care
• Basic replacement typically requires removing access panels and unplugging the blower connector; transfer any mounting grommets or brackets as needed

This AC fan motor is the refrigerator fan motor that circulates air to maintain proper cooling and airflow. It replaces a worn or failed fan motor to help restore steady airflow and consistent temperatures. What it does:

• Spins the evaporator/condenser fan blade to move air through the refrigerator cooling system
• Restores airflow when fan has stopped running or runs intermittently
• Reduces unusual fan noise or vibration caused by a failing motor
• Helps correct uneven cooling or frost build-up linked to poor air circulation

• Disconnect power to the appliance before starting any work
• Handle the fan blades carefully to avoid bending or injury
• Verify fan blade seating and clearances during reassembly to prevent rubbing

This electronic inverter motor assembly controls variable motor speed for compatible appliances, restoring smooth, efficient drive performance. Replaces a worn or failed inverter module to help resolve intermittent motor operation and speed-control issues. What it does:

• Converts control signals into variable motor speed for precise operation
• Restores consistent motor startup and RPM regulation
• Helps address symptoms like irregular motor speeds, intermittent runs, or error codes related to motor drive
• Works as the appliance's electronic drive interface between the control board and motor

• Disconnect power before servicing to avoid shock or injury
• Handle the module and connectors carefully to prevent ESD or damage
• Basic hand tools are typically required; follow the appliance service manual for access and mounting

This AC/DC fan motor circulates air inside the appliance to maintain proper airflow for cooling and ventilation. Replace a noisy, non-spinning, or intermittently running fan to restore normal airflow and appliance performance. What it does:

• Powers the fan blade to move air for cooling, ventilation, or heat distribution.
• Commonly used to replace motors that hum, don't start, or run inconsistently.
• Helps prevent overheating by maintaining airflow over components or compartments.
• Works with existing fan blades and mounting hardware when compatible.

• One fan motor (identical to the listed part number)

• Disconnect power before starting and verify the appliance is de-energized.
• Note and reconnect wiring exactly as found; mark harnesses or take a photo before removal.
• Use basic hand tools; support the fan assembly while removing and installing the motor.

The Blower Tangential 45mm is an OEM part for GE gas ranges. It is the convection fan that circulates heated air within the oven cavity during convection cooking cycles.

Symptoms of a bad blower tangential include:

• Lack of airflow inside the oven
• Uneven baking and roasting results  
• Inability to select convection cooking modes

Causes of failure can be worn bearings, burned out motor, or damage from excess heat over long-term use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. 

A 45 mm tangential blower that restores directed airflow in heating and cooling cavities to help maintain even temperatures and protect internal components. Fits factory blower mounts and connects to existing wiring harnesses. What it does:

• Moves air along the oven/cabinet cavity to promote even heat distribution and help vent hot spots
• Cools nearby electronics and components to reduce overheating risk
• Replaces worn or noisy blowers to restore proper airflow and reduce unusual motor noise
• Helps maintain designed airflow for venting and exhaust paths

• Disconnect power at the breaker before starting any repair
• Handle with care; blower edges and surrounding sheet metal may be sharp
• Verify blower orientation and wiring match the original before securing
• Basic hand tools typically needed; follow for panel removal and reassembly