General Electric Motor

Made by GE. This microwave stirrer motor comes with a square shaped shaft and is usually located in the upper part of the microwave. For a D shaped shaft turntable motor order WB26X10038.

This condenser fan motor circulates air across the refrigerator condenser to help remove heat and support efficient cooling. Replacing a faulty motor restores proper condenser airflow and can prevent temperature rise and compressor overwork. What it does:

• Spins the condenser fan to draw air across condenser coils, aiding heat dissipation
• Helps the compressor run efficiently by preventing condenser overheating
• Common symptoms of failure: refrigerator or freezer running warm, motor not running, humming, or loud/abnormal fan noise
• Can cause longer run cycles and higher energy use when airflow is restricted or stopped

• Disconnect power to the appliance before starting any repair
• Handle the fan blade and condenser fins carefully to avoid damage
• Verify wiring and mounting locations match the original; secure all connectors and fasteners

This turntable motor rotates the microwave's glass tray during cooking. Replacing a worn or seized motor restores smooth, consistent tray movement to help ensure even heating and reliable performance.

• Drives the turntable shaft/coupler to rotate the glass tray during cook cycles
• Helps promote more even cooking and defrosting
• Common symptoms of failure: tray doesn't turn, intermittent or jerky rotation, loud humming/grinding from beneath the cavity

• Disconnect power before servicing; microwaves contain high-voltage components—use caution
• Access is typically from the bottom of the unit; remove the tray and coupler, then the motor's mounting screws, and transfer the wire connections
• Align the motor shaft with the coupler and ensure the tray spins freely before reassembly
• Test with a microwave-safe cup of water to ensure smooth rotation

This is the convection fan motor for select ovens. It drives the rear convection fan to circulate hot air for more even baking and roasting performance.

• Spins the convection fan to move heated air throughout the oven cavity
• Helps protect against uneven cooking, hot spots, or longer preheat times
• A failed motor may hum, seize, not start, or run noisily
• Restores proper convection airflow when the original motor wears out

• Disconnect power before service; oven parts and wiring can be live and hot
• Access is typically from the rear or through the oven interior; remove the fan blade and mounting screws to replace the motor
• Transfer any brackets or wiring in the same orientation; note wire positions or take a photo
• After install, verify the fan spins freely by hand before restoring power

Turntable motor that rotates the microwave's glass tray to promote even cooking and restore proper tray movement. Replacing a worn motor helps eliminate stalling, grinding, or no-spin problems. What it does:

• Turns the glass turntable so food rotates for even heating.
• Replaces a motor that causes the tray to stop rotating or to spin intermittently.
• Addresses motor noises such as humming, grinding, or clicking tied to a failing drive.
• Restores smooth, consistent rotation when the original motor has worn out.

• Disconnect power before servicing and remove the glass tray and roller ring first.
• Access the motor from the cavity floor or rear panel depending on model; unplug the motor connector and remove mounting fasteners before swapping.
• Test rotation with the microwave empty and power restored before final reassembly.

Note: Motor only - convect fan WB2X8351 not included.

This turntable motor replaces the drive that spins the microwave glass tray so food heats evenly. The assembly includes the mounting gasket and restores smooth, consistent rotation when the original motor is seized, noisy, or stalls under load.

• Rotates the glass tray at a steady speed for even cooking and reheating
• Common symptoms of failure: tray not turning, intermittent rotation, loud humming or grinding
• Included gasket helps properly seal and cushion the motor mount

• Disconnect power before service; microwaves contain a high-voltage capacitor that can retain a charge
• Remove the glass tray and support ring; access the motor from the unit's underside
• Transfer/install the gasket in the same orientation; align the motor shaft with the coupler and secure with existing hardware
• Reconnect wiring and test turntable operation before reassembly

This replacement motor restores reliable rotation to the component it powers, helping your appliance operate smoothly and as designed. Swap out a worn or seized motor to bring motion and performance back to normal.

• Supplies rotational power to the attached mechanism inside the appliance
• Common failure symptoms: no movement, humming without turning, grinding/squealing noises, or intermittent/slow operation
• A failed motor can lead to loss of function and unusual noise from the driven part
• Replacing the motor restores proper motion and helps maintain overall performance

• Disconnect power to the appliance before servicing
• Access the motor area; note wire locations and the motor's orientation before removal
• Transfer any brackets, grommets, or screws from the old motor as needed; beware of sharp edges
• After mounting, ensure the shaft/attached part spins freely and clear of obstructions before reassembly and testing

This AC synchronous motor drives timed or fixed-speed rotations in compatible appliances to restore reliable timing and rotation. Ideal when a worn motor prevents timers, clocks or small gear-driven functions from operating. What it does:

• Turns at a constant, AC-synchronous speed to drive timers, clocks or small mechanical linkages.
• Replaces a failed or noisy timer/clock motor to restore timed functions.
• Common symptoms: appliance clock or timer won't advance, no rotation of small mechanisms, or intermittent timer operation.
• Operates as a direct replacement for the listed part number when matched to the appliance's OEM specification.

• Always disconnect power at the breaker or unplug the appliance before starting any repair.
• Note or photograph original wire locations and mounting orientation to ensure correct reconnection.
• Use basic hand tools; some models require removing a control panel or control box to access the motor.

This genuine replacement part is a fan motor assembly for refrigerators. The fan motor assembly circulates air through the fresh food compartment and allows for efficient cooling of that compartment keeping produce fresh. If cool air is no longer circulating through the fresh food compartment and produce is beginning to go bad, then it might be time to replace the fan motor assembly. Luckily this is a relatively easy repair.To begin, start off by shutting down all power to the appliance. Once the power has been cut, proceed to move the refrigerator away from the wall. Access the lower back panel of the refrigerator and remove it to gain access to the fan motor assembly. Remove the mounting screws that hold the assembly in place and remove the wire harness attached to the fan motor assembly. Insert the wires into the new unit, and secure the new fan assembly back to its original place.This OEM replacement part is compatible with General Electric, RCA, and Hotpoint appliances.

This part is a genuine OEM replacement motor and inverter board assembly. It is intended to replace a broken or faulty motor and inverter in various washing machine models.This part works to ensure that the washing machine's basket rotates and agitates when the appropriate settings are selected. It the motor and inverter are broken, the washing machine may not work properly or may work less powerfully than intended. This can cause clothes and materials to come out still dirty, thus this part will need to be replaced. This particular assembly includes the inverter board as well as the motor, which controls the speed and direction of the basket. Wear gloves when working on any appliance repairs to prevent injury.This part has been made by General Electric and has been sourced directly from the manufacturer. It is made out of high-quality, durable, non-corrosive materials to ensure high quality and is sold individually. It is compatible with washing machine models that have been manufactured by General Electric, Hotpoint, RCA and various other brands.

This ventilation motor drives the vent fan to remove smoke, steam and cooking odors from the range hood assembly. It restores proper airflow so the ventilation system can clear air more effectively during use. What it does

• Replaces a worn or failed vent fan motor so the hood or microwave exhaust regains suction.
• Helps stop symptoms like no airflow, weak exhaust, or unusual motor noise during vent operation.
• Works with the fan/blower assembly to move air through the vent duct and filters.
• Matches OEM function and mounting so it integrates with the existing blower housing.

• One motor-ventilation (single motor unit)

• Install only with the appliance unplugged or power turned off at the breaker.
• Handle the motor and wiring harness carefully; reconnect all plugs and fasteners exactly as removed.
• Verify fan spins freely after installation before reassembling covers or panels.

The Tray Motor is an OEM part for GE microwaves. It is the component responsible for smoothly rotating the turntable tray during operation. A functioning tray motor ensures even heat distribution for consistent cooking results. 

Causes of a bad tray motor can include wearing of internal bushings or bearings, defects in the windings, or damage from liquid intrusion over time.

Symptoms of a bad tray motor include: 

• Turntable tray not spinning or rotating unevenly
• "Turntable On" indicator blinking or remaining constantly lit  
• Burnt or cold spots on cooked food items
• Loud grinding or clicking noises coming from inside

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore microwave models. 

Single-speed PSC motor that restores rotational drive to the appliance. Replaces a worn or failing motor to stop humming, no-spin or intermittent operation and helps return steady rotation when the rest of the drive system is serviceable. What it does:

• Converts electrical power into mechanical rotation to drive the appliance's rotating components.
• Common signs a motor needs replacement: humming, no rotation, slow or intermittent rotation, or unusual motor smells.
• Replaces a failed motor to restore normal, consistent rotation when the motor is the root cause.
• Designed for direct replacement where the same mounting and wiring are used.

• Always disconnect power to the appliance before beginning service.
• Follow the appliance service manual and wiring diagrams; label or photograph connections before removal.
• Support drum/assembly as required when removing or installing the motor; avoid strain on wiring.

This 2-speed clutchless motor replaces the washer's drive motor to restore agitation and spin without a mechanical clutch. It provides the two common drive speeds used for agitate and spin cycles on compatible top-load washers. What it does:

• Turns the washer tub/agitation mechanism to enable agitate and spin functions
• Operates at two speeds (agitate and spin) using an internal clutchless design
• Commonly used when a washer hums, runs but won't agitate or spin, or fails to change between agitate and spin
• Works with the existing mounting bracket and wiring harness on compatible models

• Disconnect power before servicing to avoid shock or injury
• Motor is heavy and may require lifting assistance; support the tub during removal/installation
• Reuse the existing mounting hardware and wiring harness
• Follow the washer's service manual for disassembly, torque, and wiring routing; test operation before reassembling the cabinet

This motor assembly kit replaces a worn or failed motor to restore proper mechanical drive and motion in the appliance. It's a direct-fit replacement designed to match the original assembly's form and function. What it does:

• Replaces the appliance's motor assembly to restore spinning, stirring, or drive motion
• Stops symptoms like no movement, intermittent operation, or unusual humming from the motor area
• Restores correct mechanical linkage between the motor and driven components
• Matches OEM fit and mounting points to simplify replacement

• One motor assembly kit (single complete motor assembly)

• Turn off power to the appliance at the breaker or unplug before beginning any repair
• Follow OEM disassembly steps to access the motor area; keep fasteners and small parts organized
• Handle electrical connectors carefully; wiring matches diagrams before re-energizing