General Electric Screws, Nuts, Washers

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

This hex washer head screw secures appliance panels and brackets. The 10-16 x 0.812 size replaces missing or stripped hardware so components stay properly fastened, helping prevent looseness, rattling, and misalignment.

• Fastens metal panels, brackets, and components in compatible appliances
• Replaces a lost, damaged, or corroded screw to restore proper attachment
• Helps reduce vibration, noise, or loose-fitting parts caused by missing hardware
• Correct 10-16 thread and 0.812-inch length for specified mounting points

• Disconnect power; for gas models, also shut off the gas supply.
• Note the original screw's location and orientation before removal.
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing.
• Use a nut driver or socket that fits the hex head.

A replacement baffle screw and flat washer used to secure the baffle or trim piece in ovens and ranges. Restores proper attachment to reduce vibration and keep the baffle aligned for normal operation. What it does

• Secures the baffle or trim to the oven/range body and prevents movement or rattling.
• Replaces missing, stripped, or corroded mounting hardware that can cause loose or misaligned baffles.
• Helps maintain a tight fit so trim and baffle sit flush with surrounding panels.
• Small, direct-replacement fastener for original baffle mounting points.

• Disconnect power and allow the appliance to cool before accessing internal panels.
• Use the matching size screwdriver; start threads by hand to avoid cross-threading.
• Tighten until snug — avoid over-tightening, which can strip threads or deform the washer.
• Repair or replace the mounting bracket before installing this hardware.

This is a genuine OEM replacement nut that is used on convection oven fans. This nut holds the fan onto the spindle. If the nut becomes lost during repairs to the fan, it will need to be replaced before the fan will work. This nut locks the fan to the spindle to turn and move the air around inside the oven. The fan helps the food to cook more evenly and reduces areas in the oven that are not cool enough or hot enough. If the fan is not working, the convection oven will not cook correctly.Convection ovens are different from regular ovens, and the fan is part of the reason. Convection ovens use the fan and an exhaust system to move the heat around inside the oven to cook food more evenly and faster. Many convection ovens have a setting that allows the oven to be used as a regular oven. If the nut is missing and the fan is inoperable, the oven can be used for regular cooking if it has this feature. Otherwise, the convection oven should not be used until the nut is replaced.This nut is a silver metal replacement part that is sold individually. It is designed for use in convection ovens made by GE and Kenmore.

ST10-16 X 7/16"

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

This hex nut secures components within the range or cooktop assembly, helping keep parts tight and aligned. Replace a missing, stripped, or corroded nut to restore a solid fit and reduce rattling or loosening during use.

• Provides threaded fastening to hold mating parts together securely
• Replaces worn, stripped, or rusted hardware that no longer tightens properly
• Can help resolve loose or wobbly components and rattling noises
• Built to match the original fastener for proper fit in compatible appliances

• Disconnect power and shut off gas before servicing
• Start threads by hand to avoid cross-threading; tighten only until snug with the appropriate wrench
• Note the order of any washers/spacers during removal to ensure correct reassembly

A 1/4-20 x 5/8 hex washer-head machine screw that secures brackets, panels, and internal components in your appliance. Using the correct fastener keeps assemblies tight to help reduce vibration, rattling, and alignment issues.

• Provides the specified 1/4-20 machine-thread fastening for designated mounting points
• Replaces a missing, stripped, or damaged mounting screw
• Helps reduce loose-component rattles and vibration
• Maintains proper alignment of brackets, panels, and hardware

• Disconnect power; for washers, also shut off water before service
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Use the appropriate nut driver or socket for the hex-washer head
• Install only where this thread and length are specified by the manufacturer

This #8-18 x 5/8-inch Torx T20 screw secures panels, brackets, and trim in your appliance. It replaces missing or damaged hardware to restore a tight, reliable hold and reduce looseness or rattling.

• Fastens sheet-metal or plastic components to the appliance cabinet or frame
• Replaces missing, stripped, or corroded screws to maintain proper fit
• Helps reduce vibration and rattling from unsecured parts
• Torx T20 drive; #8-18 thread; 5/8-inch length

• Disconnect power and shut off water before servicing
• Use a T20 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping
• Wear cut-resistant gloves; sheet-metal edges can be sharp

Includes 12 washers.

This chamfered nut is a genuine fastener used to secure mating parts inside your appliance. It replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and proper alignment.

• Provides threaded clamping force to fasten components
• Helps maintain alignment and resist loosening from vibration and heat cycles
• Replaces rounded, stripped, corroded, or missing nut
• Typical symptoms: loose panels/brackets, rattling noises, or parts shifting out of place

• Disconnect electrical power; turn off gas supply before servicing
• Allow the appliance to cool completely; wear gloves and eye protection
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Match orientation/position to the original

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

Black. 8-18 AB HXW 3/8

Size: 8-18 AB TSQ 5/8 SS

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal