Hinge Parts

Snap bushing installs in door panel openings to protect wiring or tubing. Replace if cracked, missing, or worn to prevent chafing and pinching.

Securely attaches the oven door to the range cabinet. Replace if your hinge is cracked, bent, worn, or causing the door to hang unevenly or not close properly.

This door hinge supports and pivots the appliance door for smooth, aligned opening and closing. Replacing a worn hinge restores proper closing and helps the latch and door seal make consistent contact. What it does:

• Provides the pivot point and structural support for the door
• Maintains door alignment for correct latch engagement and seal contact
• Helps prevent binding, sagging, uneven movement, and squeaks
• Common fix for doors that won't close fully or feel loose/wobbly
• Replaces hinges that are bent, cracked, or show excessive play

• 1 door hinge

• Disconnect power (and shut off gas/water if applicable) before servicing
• Support the door to prevent strain; removal may be required to access the hinge
• Remove hinge cover/trim and mounting screws; transfer any hardware to the new hinge
• After installation, verify alignment and closure; adjust as needed for proper latch and seal contact

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.

• Provides a soft stop between the lid and top to minimize noise and vibration
• Helps prevent chips, scratches, and rust where the lid meets the cabinet
• Maintains proper lid spacing for a solid, rattle-free close
• Common signs it's needed: missing/flattened bumper, louder closing, rattling, or visible wear at contact points

• Disconnect power before servicing
• Open the lid, remove the old bumper, and clean the mounting area
• Seat the new bumper fully in the mounting location as designed
• Open/close the lid to ensure quiet, secure contact

Replacement oven door hinge for ranges. Supports and guides the door through opening and closing. Install when original hinge is broken, worn, or fatigued.

Grey left-hand door closer cam for bottom-mount refrigerators. Replaces broken or worn door closers that prevent proper door alignment and sealing.

Rotating cam mechanism that mounts inside the refrigerator door to gently pull it closed. Replace if cracked, broken, or worn causing poor door closure.

Replace worn, damaged, or broken range door hinges. Installs on both ends of the oven door to enable smooth opening and closing. Essential when hinges fail.

Lower hinge pin serves as the pivot shaft for your refrigerator door. Replace this part if worn, bent, broken, or missing to restore smooth door movement.

Metal pivot pin for the center hinge on refrigerator doors. Restores smooth door swing and proper alignment when original pin is worn or broken.

Replace your worn or broken refrigerator bottom hinge pin. Supports the door and serves as the lower pivot point on the bottom hinge assembly.

Gray door hinge for side-by-side refrigerators. Replaces cracked, broken, or worn hinges that cause misalignment or sagging doors.

This arm hinge assembly restores smooth, controlled movement of a hinged component in your dishwasher, helping maintain proper alignment and reliable operation. Replacing a worn or broken hinge can reduce binding, squeaks, and misalignment that affect performance. What it does:

• Provides the pivot point and support for a hinged assembly
• Maintains alignment to ensure correct engagement and sealing
• Helps ensure smooth opening/closing motion without binding
• Replaces a hinge arm that is cracked, bent, or worn
• Common signs: stiff or uneven movement, squeaking or popping noises, misalignment, or visible damage

• 1 arm hinge assembly

• Disconnect power and water before servicing
• Support the door or movable assembly to relieve tension while removing the hinge
• Note orientation and transfer any side-specific hardware from the original part
• After installation, check for smooth motion and proper alignment before restoring power and water

Pivoting hinge that supports and guides your dishwasher door. Replace if cracked, worn, or causing door sagging, misalignment, or scraping during operation.

This refrigerator dispenser bearing supports the auger shaft so it spins smoothly during ice dispensing. Replacing a worn bearing restores quieter, more reliable ice delivery and helps prevent binding or uneven crushing of cubes. What it does

• Supports and centers the ice auger/crusher shaft inside the ice bucket
• Reduces friction to allow smooth, consistent rotation
• Wear can cause grinding or squealing during dispensing
• Symptoms include slow/no ice dispensing, jamming, or intermittent operation

• 1 bearing

• Disconnect power and turn off the water supply before service
• Remove the ice bucket and disassemble the crusher housing to access the bearing
• Note the bearing's orientation; transfer any spacers or clips as found
• Reassemble carefully and ensure the auger turns freely by hand before restoring power