Kenmore Ice Maker 1068440 Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196157
The Icemaker Fill Tube Fitting is an OEM part for Whirlpool refrigerators. This part connects the water supply line to the icemaker, ensuring a seamless and leak-free delivery of water into the icemaker mold.
Causes of a bad Icemaker Fill Tube Fitting can include wear and tear over time, mineral buildup from hard water, which can block the water flow or damage the fitting, and improper installation that may lead to leaks or restricted water flow.
Symptoms of a bad Icemaker Fill Tube Fitting include:
- Water leakage at the connection points, leading to potential water damage or ice buildup in the freezer
- Insufficient ice production if the fitting is partially blocked or not properly connected, restricting water flow to the icemaker
- Unusual noise during the icemaker fill cycle, indicating a potential issue with the fitting
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
This part fixes the following symptoms
-
Not dispensing water
-
Ice maker not making ice
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
Ice maker fill tube leak Chad M. • Hollywood , FL • May 16, 2015
I watched your how-to video. It explained the repair PERFECTLY.
It was an easy repair and the video was very detailed. It took the guesswork out of the repair.
I was done in 5 minutes.
thanks for taking the time to post videos for your parts. I'll shop here again.
Best Regards,
Chad M
Read more
More
$9.60
- Compare At:
-
$11.52
- You Save:
-
$1.92
Genuine Whirlpool part
By: Whirlpool
Part Number: W10823511
The Ice Maker Water Line is an OEM part for Whirlpool refrigerators. It supplies water from the household plumbing to the ice maker, ensuring a consistent and reliable production of ice cubes. This kit includes a 1/4-inch plastic water line that is approximately 72 inches long. The tubing will need to be cut to match the desired length.
Causes of a bad water line can include wear and tear from prolonged use, kinks or bends restricting water flow, or leaks due to punctures or cracks. A compromised water line can result in inadequate ice production or water leaks.
Symptoms of a bad ice maker water line include:
- Reduced or no ice production
- Leaking water from the refrigerator
- Visible cracks or damage to the water line
- Ice cubes that are smaller than usual
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Not dispensing water
-
Ice maker not making ice
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
Ice maker fill tube leak Chad M. • Hollywood , FL • May 16, 2015
I watched your how-to video. It explained the repair PERFECTLY.
It was an easy repair and the video was very detailed. It took the guesswork out of the repair.
I was done in 5 minutes.
thanks for taking the time to post videos for your parts. I'll shop here again.
Best Regards,
Chad M
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 4318047
The Single Water Valve is an OEM part for Whirlpool refrigerators. This valve controls the flow of water to the refrigerator’s ice maker and water dispenser, ensuring a consistent and reliable supply of water for ice production and dispensing.
Causes of a bad single water valve can include wear and tear over time, mineral buildup from hard water, or electrical malfunctions.
Symptoms of a bad single water valve include:
- No water dispensing from the refrigerator
- The ice maker not producing ice
- Leaks around the valve area
- Unusual noises when the water dispenser is activated
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
This part fixes the following symptoms
-
Ice maker not making ice
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
Leaking valve on ice maker Richard D. • Front Royal , VA • March 15, 2014
Order new valve
Read more
More
$44.95
- Compare At:
-
$53.04
- You Save:
-
$8.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP627018
Size: 1/4 inch. Nut for plastic water line.
Do-It-Yourself Stories from Customers like You
Broken y connector off of water valve on amana refridgerator Greg S. • El Dorado Hills , CA • October 19, 2014
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks.
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 4387491
These inserts are for 1/4 inch plastic tubing. Package of 4.
More
$11.95
- Compare At:
-
$13.22
- You Save:
-
$1.27
Genuine Whirlpool part
By: Whirlpool
Part Number: 285448A
This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.
- Distributes load and provides proper spacing in the fastener assembly
- Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
- Direct replacement when the original washer is worn, bent, cracked, or missing
- Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service
What's included: 1 washer Install notes:
- Unplug the appliance; shut off water supply if working near hoses or valves
- Note the original hardware stack-up and reassemble in the same order
- Inspect mating surfaces and companion hardware; replace any damaged parts
- Tighten fasteners snugly per service guidance; avoid overtightening
Do-It-Yourself Stories from Customers like You
Wash machine water inlet valve Larry E. • Coleharbor , ND • February 18, 2017
Watched a video online, the project took about 20 minutes, went well, parts fit good, the video was very helpful in getting the wash machine up and running.
Read more
More
$5.34
- Compare At:
-
$6.35
- You Save:
-
$1.01
Genuine Whirlpool part
By: Whirlpool
Part Number: WP488878
This hose clamp secures a rubber or plastic hose to its fitting on your appliance, maintaining a tight, leak-resistant seal under vibration and pressure. Replace when the old clamp is rusted, bent, or no longer holds tension. What it does:
- Clamps around a hose to grip the fitting and seal the joint
- Helps prevent drips, leaks, and hose blow-off at the connection
- Restores secure clamping force when the original is worn or damaged
- Common symptoms: water at the connection, hose slipping off, visible corrosion or distortion
What's included:
Install notes:
- Disconnect power and shut off the water supply before servicing
- Slide clamp onto hose, seat hose fully on the fitting, then position clamp just behind the bead/raised lip
- Tighten or compress evenly with the appropriate tool; avoid overtightening that could damage the hose
- After reassembly, run a short test and inspect for leaks
Also known as: Tube clamp
More
$7.49
- Compare At:
-
$8.84
- You Save:
-
$1.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP488366
This spring-style tube clamp secures flexible tubing to fittings, helping prevent leaks and maintain proper flow. It's a simple replacement that restores a firm seal on water or drain lines. What it does:
- Keeps flexible tubing firmly clamped to barbed or nipple fittings
- Helps stop or reduce leaks from loose or corroded connections
- Prevents tubing from slipping off under pressure or vibration
- Useful where a compact, spring-action clamp is required
What's included: One spring-style tube clamp as shown Install notes:
- Disconnect power and shut off water to the appliance before replacing parts
- Use pliers to expand the clamp, position it over the tube/fitting, then release to secure
- Inspect connected tubing and fittings for damage; replace if cracked or severely corroded
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2158826
This dampener cushions and stabilizes the washer tub during spin cycles to reduce vibration and noise for smoother operation. It replaces worn or damaged suspension dampeners to help restore proper tub balance and quieter performance. What it does:
- Absorbs and dampens tub movement during agitation and spin to reduce vibration and noise.
- Helps maintain proper tub alignment for more even spinning and less wobble.
- Commonly replaced when the washer rocks, thumps, or makes excessive noise during spin.
- Works with the washer's suspension system to protect other components from shock and wear.
What's included:
Install notes:
- Disconnect power and shut off water supply before beginning any repair.
- Access typically requires removing the washer cabinet or front panel; follow OEM service instructions.
- Inspect mounting studs and clips for wear; replace as needed to ensure a secure fit.
More
$0.95
- Compare At:
-
$1.13
- You Save:
-
$0.18
Genuine Whirlpool part
By: Whirlpool
Part Number: W11625904
This replacement ice cube pan holds and organizes ice in your refrigerator's freezer. Replacing a cracked or warped pan restores clean, contained ice storage and smoother access or dispensing, depending on your model's design. What it does:
- Collects and stores ice produced by the icemaker or manual trays
- Keeps cubes contained and easy to access; fits designated guides in the freezer
- Helps ensure proper ice access or dispensing on applicable models
- Typical symptoms: cracked bin, broken tabs, bin won't seat, ice spilling or clumping
What's included:
Install notes:
- Disconnect power to the refrigerator and turn off the icemaker before starting
- Remove the old pan and empty any remaining ice
- If your model reuses a drive/crusher or other hardware, transfer those parts from the original pan as directed for your unit
- Seat the new pan fully in its tracks/coupler, restore power, and allow normal ice production
Do-It-Yourself Stories from Customers like You
Needed replacement Elizabeth A. • Pittsboro , NC • March 01, 2016
Part came with great speed.
Read more
More
$43.95
- Compare At:
-
$52.30
- You Save:
-
$8.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP628210
Do-It-Yourself Stories from Customers like You
Ice maker leaking water into the ice tray David M. • Wayne , PA • September 04, 2015
Replaced broken gear
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 4378431
Genuine Whirlpool part
By: Whirlpool
Part Number: 625851
Do-It-Yourself Stories from Customers like You
Ice dispenser wasn't working Karen K. • Highland Falls , NY • June 13, 2015
Replaced the limit switch.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP625834
Do-It-Yourself Stories from Customers like You
Ice chute on front of door stopped working Phillip B. • Killeen , TX • December 08, 2014
I found the correct part on the website that I needed very easily and received it within two days with only regular shipping. The email I received letting me know that my parts were on the way also included a YouTube link that showed me exactly how to remove the broken part and install the new part. Total installation time was about 20 minutes from start to finish.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 480855