John September 12, 2020 for Model Number FGHD2455LW0 Dishwasher will not run unless we unplug it. Then is says PF (Power Failure). We then restart and it will run thru a cycle or 2. Then the whole thing starts over again. Unplug and run cycles. It is taking longer for it to work between the times when we unplug now. It now takes an hour to reset by unplugging, when it first started doing this it would reset right away when we plugged it back in. The display board works as well as all of the led lights. Before we unplug after a cycle nothing works or lights up until we unplug and start all over again. Then everything works for one cycle. Thanks
1 Answer John, based on the information provided it sounds as if you have an electronic control board issue. The board part number is. 5304480721 Read More...
Lawanda October 08, 2018 for Model Number FGHD2455LW0A ER code flashing after a power surge and the electricity going out in my neighborhood. I reset the breaker to no avail. I've unplugged it for a couple of days too. I was able to reset it at one point, but it started and ran for about 5 minutes and got the error again. Then while pushing buttons to just try to get it to do something it started putting random numbers on the display screen. Now back to error again. Control panel?? Part number, please. Thanks!!!
1 Answer Lawanda, The manufacturer says that error is for a switch failure meaning your user interface probably has a short in the membrane. Unfortunately, the manufacturer doesn't provide a key chart to test the user interface. Without being able to rule out for sure the interface or main control it could be either one. 5304480721 is the control and 5304480722 is the interface. Read More...
Mark August 28, 2017 for Model Number FGHD2455LB0 All buttons on the panel work except the "Start" and "Delay Start" buttons. Unit will not start.
1 Answer Mark, You will want to make sure that door switches are good on the unit and if they check ok then this will most likely be a faulty control panel on the unit. Read More...
Wade January 29, 2017 for Model Number FGHD2455NF1A i push favorites and washer begins for about ten seconds then quits and ER pops up. The rinse led light stays on and when I push start/cancel it seems to start its cycle and quits again. I've repeated this several times and same thing. I've even tried to reset and actually turn power off to it and waited. Still the same thing. Which is bad control board or push button panel?
1 Answer Wade, This issue would be caused by a faulty control panel which has a key stuck and would be part number. This would require the control panel to be replaced. Read More...
Warren July 08, 2016 for Model Number FGHD2455LF0 Display stays at 99 and somethings counts down but does not seem to get the dishes clean . Replaced the pump and still does the same thing.If I cancel the water pumps out and stops.
1 Answer Warren, You will want to check to see if there is power getting to the pump in the wash cycle. If it is not then the issue may be that the control board is faulty and would need to be replaced. Read More...
Joe July 05, 2016 for Model Number FGHD2455LWOA Washer fills and empties with no problem. Sometimes it will complete the prewash cycle and others it just does nothing until the next empty cycle occurs. Following the prewash there is no humming other evidence that it is trying to do something. Thinking it might be the board or a loose connection somewhere. Thanks.
1 Answer Hello Joe. Check all the wiring and if it looks good, then you will need to order and replace the main board on the unit. Read More...
Janice January 24, 2016 for Model Number FGHD2455LW0 The dishwasher doesn't seem to dry dishes and when you open it after running it doesn't have a lot of steam coming out. Mold and odors are bad inside especially in the screen filter. Dishes don't get very clean and oily residue on dishes. Have checked continuity of heating element and it seems to be good. Would the next likely item be the thermostat assembly?
1 Answer Hello Janice, The issues with the heating circuit can be caused by the heater, the heater thermostat, the neutral door switch, or the control. You should also make sure the unit is secured properly under the countertop. If it is not secure and can move around, it may not be making the door switch properly for normal operation to occur. Read More...
Dennis June 12, 2014 for Model Number FGHD2455LB0A Dishwasher showed "ER" on digital display and would not begin wash. Pressed "START Cancel" and the display cleared. Now it does not do anything. The green light next to "Hold to lock" is lit, but nothing else displays. Did not have any intermittent problems before this happened.
1 Answer Hello Dennis. You will need to check for a stuck button. Also, check and see if the unit will unlock. If not, replace the touch pad. Read More...