Randy November 19, 2018 for Model Number 362.72622300 I am unable to calibrate the oven temp on my Kenmore oven. I replaced the temp probe thinking it was the cause of some low temps readings. I Held the bake switch for 15 sec but the control Board never registered 00 so that I could adjust the temp up or down to calibrate. Would this control board be the likely cause of this problem. Thanks for the help!
1 Answer Randy, The bake temperature can be adjusted from its factory calibration by (+or-) 35 degrees F in 1 degree increments 1.Press and hold both the BAKE and BROIL pads for about 2 seconds until the display shows SF. 2.Press the BAKE pad. A two digit number shows in the display. 3.Press the + pad to increase the temperature in 1 degree increments or press - pad to decrease the temperature in 1 degree increments. 4.Press START key. Read More...
Glenn April 25, 2018 I can not turn the oven or broiler on from the control panel. The oven will come on when I put in self clean mode. The clock, kitchen timer and burners all work. Is the problem with the control panel or something else? Is there a way to test the control panel? I don't want to buy a control panel if that is not the problem.
1 Answer Glenn, For this issue the control board will be the most likely cause for the issue of the bake and broil not working. Read More...
Dave March 06, 2016 for Model Number GE Stovetop JP980 I replaced the front right burner unit, but cannot get through the calibration process. The process fails on the LR burner and I am unable to continue the process. Should I replace that burner, or is this related to the main logic board?
1 Answer Dave, With the unit not completing the calibration mode, you will want to check the wiring and do a continuity test of the inductive sensors. If this checks ok then the control would be the issue. Read More...
David February 20, 2015 My Kenmore gas stove will not preheat but the broiler ,stovetop and clock all work. What do you think is wrong?
1 Answer Hello David. It sounds like the control board is bad and will need to be replaced on the unit. Read More...
Frank December 14, 2014 for Model Number jgbp28bej1ct I get a f7 code and the oven will not work. Will this fix problem. I read a button is stuck or buttons not working right and if I order this do I need to buy the overlay part also?
Sonia November 16, 2013 for Model Number Jgbp28deh1ct I changed both igniters broil now works ,but when I plugged the stove back into the wall oven igniter comes on without by itself without turning on the oven and flashes 18:88 on the control panel.
1 Answer Hello Sonia. You will need to order and replace the control board in the unit. It is bad. Read More...
Johnny November 15, 2013 for Model Number JGBP29WEK1WW Just ordered part WB27K10354 Control Oven T09 (gas) and still not working. I do get power to the unit clock works makes the beeps etc. Just can not make bake or broil to function. I ordered this part because bake and broil were not working all of a sudden and this is what I found after research. What is wrong?
1 Answer Hello Johnny. Test for power to the igniter. Also, make sure all the wiring is good on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mike July 24, 2013 Your guy just suggested I ask a tech question before I order a board for my g e range. Would a power outage at our home for 2 minutes during a storm burn out the board? The receptacle checks out fine. Everything else in the home o k, computers , tvc , etc.
1 Answer Hello Mike. If the board took the direct surge, it very well could have damaged it. Read More...
Mr. Singh March 23, 2013 for Model Number jgbp28beh1wh The control board above is a replacement from the original. The wiring is different. May I please get the installation instructions for this new part. Thanks!
1 Answer Hello Mr. Singh. According to the manufacture, the connectors on the new board are labeled the same as the old board and the wires go to the same terminals that have the same labels on them. They do not offer an instruction sheet for this part. Read More...
Elvis October 24, 2012 for Model Number JGbp28sel3ss I wanna know if this part no. AP4980366, can be used on my stove model GE, JGBP28SEL3SS?
1 Answer Hello Elvis! Yes, the oven control WB27K10354 is the correct replacement and will fit your model JGBP28SEL3SS. Thanks! Read More...