Nancy P May 01, 2019 for Model Number Kenmore Dishwasher Ultra Wash When pulling out the top rack, I accidentally popped off the top sprayer disc. We were able to find a small metal washer but don't know what part kept the sprayer disc in place. Can you help?
1 Answer Nancy, To be able to assist properly with your question we will need to have the model number of your unit. Please supply the model number and resubmit your quesiton. Read More...
Mark November 30, 2018 for Model Number GE GSD4030Y72WW During drain cycle water is leaking down from the drain solenoid, but the drain solenoid does not contact water. I cannot see or feel water above the drain solenoid, so I cannot determine what part has failed. Can you advise?
1 Answer Mark, This issue would be caused by a seal in the pump housing that in order to get this part you would need to replace the pump and motor assembly WD26X10013. Read More...
Melinda December 19, 2017 How will I know that the pump impeller is damaged? What things will I need to look for to determine this is the problem. I actually order one and it is due to be delivered today.
1 Answer Melinda, You would look for broken impeller which would be most likely cause. You will want to also check for clogs. Read More...
Melinda December 14, 2017 for Model Number GSD3600G00WW Dishwasher not draining completely at the end of cycle. I replace the piston nut assembly in 2015 and that fixed the problem, I am having same issue now I inspected the piston nut assembly and it still looks in great shape. I have checked out under neath the dishwasher and there are no leaks the valve bracket moves freely, I have checked all the filters and hoses for build up and clogs that is also good. Any suggestions?
1 Answer Melinda, You will want to check the pump impeller to make sure that it is not damaged. This will be the most likely cause for this issue. Read More...
Monty October 01, 2017 for Model Number GSD6200G00WW Does the plastic washer fit flush side to steel bearing or to chopper blade? If steel bearing has flange toward chopper blades and plastic washer has flat side towards the chopper blade then after cover on and tightened the the motor is tight and doesn't spin very easily. If turn bearings around then steel bearing rattles inside?
1 Answer Monty, The flat part of the plastic washer will face the chopper blade on the unit. Read More...
Monty October 01, 2017 for Model Number GSD6700G00WW On repair kit for leaking pump seal, which way does the steel bearing fit on the impeller? Does the flange go towards the impeller or the chopping blade?
1 Answer Hello Monty. It will only go one way properly. You want to make sure the seal is installed correct. Watch the video and he shows the way it goes at 6:00 in the video on the parts page. Thank you. Read More...
Roger March 01, 2017 for Model Number GSD3960L00ss My dishwasher continues to leak inside the machine when it's not in use. Is there a solenoid valve that controls the flow of water into the pump or is something else malfunctioning?
Kenneth S. April 12, 2016 for Model Number 36316129100 After the final cycle, water remains in the bottom of the dishwasher. I checked all the hoses and there appears to be no clog. I took apart everything where it appears that water flows through and the majority of the remaining water came out when I removed the clamp that attaches the motor assembly to the base of the dishwasher. I looked at it and there was no noticeable obstruction. I am figuring I may have to replace a part, but from research there are a few options. What is your recommendation on moving forward?
1 Answer Hello Kenneth. It sounds like the drain solenoid WD21X10060 is bad and will need to be replaced on the unit. You will need to check it and see if it is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
David October 16, 2015 The shaft on the motor is pitted up pretty bad from rust. I know the seal kit needs replacing but will the pits on the shaft leak even with the new kit?
1 Answer Hello David, Without a model number I cannot give you a specific part number but the motor shaft cannot be pitted where the seal rides or it will leak. The motor assembly should be replace at the time of service. Read More...
Dan C April 05, 2015 for Model Number gsd2230z00ww Replacing the impeller kit. The seal does not slide down the shaft. Is there a sleeve on the shaft? Is there a different seal sold?
1 Answer Dan, This impeller kit is correct for your unit and there is not a sleeve on the shaft. The seal that comes with the part is the one for the repair and may be tight sliding it down. You can try a little powder on the shaft to get it on. Read More...