R.M.H. July 14, 2018 for Model Number G82SHDXTQ01 One of the bulbs on the Whirlpool Gold refrigerator at the top with a grid is out. What size bulb does it take and how do I remove the grid so as not to break it?
1 Answer Hello R.M.H., I'm sorry but we will need to ask you to please post a new question including the verified model number from the units' I.D. tag since the one provided will not come up for us as a valid model number. Thank you for your patience and understanding in this matter. Read More...
Md October 05, 2017 for Model Number Whirlpool ed25tq I need a replacement light bulb, no more than 10w, for the outside freezer door where the ice cubes and water come out. Do you know what the part number is for that, and how I would get one?
1 Answer MD, The correct dispenser light bulb, for the partial model number you supplied is WP22002263 / WP22002263 Light Bulb. The part is in stock and available at AppliancePartsPros.com Thanks, Read More...
Paul November 23, 2016 My freezer occasionally drips water on the floor just below the freezer compartment. I have a side by side Whirlpool refrigerator. It amounts to about a cup of water, and since is doesn't happen all the time, no one seems to be able to locate the problem.
1 Answer Hello Paul. It sounds like the drain may be clogged. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. http://forum.appliancepartspros.com/refrigerator-freezer-repair/173916-kenmore-top-mount-refrig-h2o-build-up.html Read More...
Cecilia November 28, 2015 I have a Westinghouse refrigerator.The bulb burned out.I think that it's a 40 watt,anyway this is the # 120V40W,Can I buy a bulb from any company available or it has to be strictly Westinhouse's? It's blue.Please help. Thank You!!
1 Answer Cecilia, You will want to make sure that the bulb that you get is a 40 watt appliance bulb and can be any appliance bulb. Read More...
Joe March 21, 2014 for Model Number Maytag MSD2756DEW The light bulb (AP4067417) behind the Crisp is burned out. How can I reach and remove its light shield (AP4069482) in order to reach the bulb ? Thank you.
1 Answer Hello Joe. Pull down on the back corners of the cover and slide the cover forward to remove. Read More...
B.P. February 26, 2014 for Model Number MAYTAG-MBF 1956HES How do I replace the burned out light bulb in the refrigerator side?
1 Answer Hello B.P., In model MBF1956HES, you will need to depress the retention tabs on the backside of the light lens. This will release it and you can set it aside. Remove the burned bulb and install the new one. I normally hold the door switch in while installing the new bulb to prevent the possibility of the new bulb burning out due to the power surge through it. Read More...
Joseph January 28, 2014 for Model Number Maytag MSD2356AE Hi the refrigerator and the freezer is too cold even on the lowest #1 setting for both refrigerator -9C and freezer -20C. I have purchased parts from this site to replace few parts in the past on this fridge the temp control housing etc. Please advise, thanks
1 Answer Joseph, With the temp getting down to 15 degrees Fahrenheit in the refrigerator compartment and -4 in the freezer then the issue would most likely be caused by a faulty auto damper which comes as part of the auto housing assembly WP61005993. Read More...
Sandy P October 14, 2013 for Model Number whirlpool refrigerator et1phkxpt08 The interior light has gone out, but a replacement 60 watt bulb won't work. Does this have to be a special bulb, or is something else possibly wrong?
1 Answer Sandy, You will want to use a 40 watt appliance bulb instead of a 60 watt as the 60 will get hotter than the 40. When you do install it the bulb will get to a point where it feels like it is all the way in. If you turn it just a little bit more it should go in further. If you have one of the rubber jar removers, this works good for getting it all the way in place. Read More...
Jerry September 20, 2012 for Model Number NS22L8 How do I remove the Light shield AP4068032 in rder to replace burned out bulb?
1 Answer Hi Jerry. Pull out both knobs. Look at the bottom back and remove the screws that mounts it to the upper cabinet. Then you can remove the bulb part # W10887190. Thank you. Read More...
Marilyn L September 18, 2012 for Model Number PSD2350DPW There is a white plastic rectilinear shield and it houses the control nobs. Must the plastic shield be lifted out to reveal the location of the bulb? This A rectilinear white plastic shield is located on the top shelf of the fridge side. Will I disturb the temperature control knobs and deactivate them if I lift out this shield? Am I looking at the proper location of the light bulb? I am concerned about being in the right area! Where the presence of the light bulb is located is not at all evident! I fear making this light bulb problem even worse! Please guide me further.
1 Answer Hello Marilyn. Yes, you must remove the light shield 61003217 to access and replace the light bulb W10887190 in the unit. Read More...