Dan May 12, 2020 for Model Number LSE7806ACE Hi I have problem about water keeps filling and does not stop. 1. My model number is LSE7806ACE 2. When it reached a certain level, it stats agitating, but water still keeps filling. 3. I disconnected the tube to the pressure sensor, and connected an another tube. I the used my mouth to blow. Water does not stop! I guess pressure sensor is good. 4. I tried replacing water inlet, still the same. I guess water inlet is good. 5. I unplugged the connectors to the water inlet, water stoped. I measured the voltage between the lead, it read 120 V, [both before agitating (meaning filling water. It should be 120 V) AND after agitating started (supposedly ZERO voltage, if I am right so that water be cut off, but it is 120V)]. 6. Does timer controls voltage to the water inlet? 7. What else should I try? Thank you so much
1 Answer Hello Dan, usually, for this problem, you would replace the water level sensor 12002304, and the airline hose (220016160) however the hose is no longer available. The airline tube has to be airtight from the tub to the level sensor is to ensure the water level is correct as read by the level sensor. If you blow (gently) into the sensor and the water kept filing it is faulty. Read More...
Dan Ives January 04, 2017 for Model Number LAT9416AAE Model LA 710 Washer - Problem - Hot water is greatly restricted. Can faint hear noise of hot/warm water trying to fill tub Cold water no problem. Would it be the valve? What would be the comparable Model # for LA 710
1 Answer Dan, You will want to check the inlet screen on the hot water connection to make sure that it is not plugged up. If it is then you will want to clean out the debris. If the problem persist then the valve part number will be 205613. Read More...
Allen April 26, 2016 for Model Number GS2SHEXNQ00 The right side has no lights and no control panel power.
1 Answer Hello Allen, You should verify voltage to the control WPW10366605. Replace if voltage is on terminal P1-1. Read More...
Allen April 25, 2016 for Model Number whirlpool GS2SHEXNQOO Right side no lights and no power to control panel, but still cold and making a noise.
1 Answer Allen, With the lights on the refrigerator side not working and the display not working, this would be cause by a main control board issue. The main control board is located next to the compressor in a box. The part number for the control board is WPW10135090 and would need to be replaced. Read More...
Allen April 25, 2016 for Model Number GS2SHEXNQ00 There are no lights on the right side and no lights in the temperature controls. It is also making a low frequency noise.
1 Answer Hello Allen, This is most likely a power supply issue on the main board WPW10135090 unless there is a connection/harness issue. Read More...
M March 08, 2016 My washer will fill up quickly in warm/hot water mode. However, when I put the select switch to cold water, it just drips in.
1 Answer M, You will want to check the screen on the cold water valve for debris build up. Pull the hose off and look inside the valve to check this and if it has debris in it then clean it out. Read More...
Mick March 03, 2016 for Model Number LAV3600AWW My washer keeps dripping in side so it has to be spun it out. It seems it won't shut off the fill valve completely. Can the fill valve itself be bad?Its a very slow drip but it's constant.
1 Answer Hello Mick, If the screens WP96160 are not stopped up and water pressure to the valve is sufficient, the water valve WP22002360 will be the issue. Read More...
Allen February 18, 2016 for Model Number kenmore 500 model 29522800 Washing machine does not finish wash cycle.
1 Answer Hello Allen. You will need to check and see if the lid switch is bad and will need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
1 Answer Allen, If the dryer turns on and gets hot but is not venting out then check the blower wheel and check the vent from the blower wheel to the outside of the home for restrictions or blockage. Read More...
Allen November 13, 2015 for Model Number maytag LSE7806ACE Dryer makes a rumbling sound on and off when drying.
1 Answer Hello Allen, This is most likely the blower wheel Y303836 causing a rumbling sound. Read More...