Amana Dryer LE1102 Will not tumble or doesn't tumble

The Belt is an OEM replacement part for Whirlpool dryers that is responsible for connecting the motor to the drum to allow it to tumble. Over time, dryer belts can stretch, wear out, or even break, leading to a drum that won't turn and clothes that don't dry properly. Length: 93 3/8" Width: 3/8" has 5 ridges.

Symptoms of a bad Dryer Belt include:

• The dryer motor running but the drum not turning.
• A squealing or thumping noise coming from the dryer.
• The dryer not starting at all.

Causes of failure can include regular wear and tear from the dryer's operation, overloading the dryer beyond its capacity, which puts extra strain on the belt, or a misalignment that causes uneven wear. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Belt Tension Pulley is an OEM part for Whirlpool clothes dryers. It utilizes a tension mechanism to maintain precise alignment and contact between the drive belts and motor pulleys during operation.

Symptoms of a failed belt tension pulley include:

• Extended dry times or inability to dry clothes fully
• Abnormal noise or vibration coming from inside the dryer
• Premature belt wear requiring frequent replacement
• Error codes appearing or inability to start cycles

Causes of a bad pulley can include cracks, defects, or stiffness in the tension mechanism limiting its range of motion from years of operation. Lubricant breakdown within the pulley can also produce excessive friction or noise over time.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Thrust Washer is an OEM part for Whirlpool washers and dryers, reduces friction between moving parts within the appliance. This small component is placed between rotating surfaces to ensure smooth operation and to extend the lifespan of those parts. The thrust washer can wear down or become damaged due to the constant pressure and movement.

Causes for replacement may include normal wear and tear, overloading the appliance, which puts extra stress on mechanical components, or a lack of regular maintenance.  

Symptoms of a bad Thrust Washer include:

• Increased noise during operation
• The appliance vibrating more than usual
• A decrease in performance efficiency

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Retaining Ring is an OEM replacement part for Whirlpool dryers and washing machines. This retaining ring holds the rear wheels on the axels of the washer or dryer. 

Symptoms of a bad retaining ring can include wear and tear over time, damage due to accident or impact, or corrosion affecting the structural integrity.

Causes of a bad retaining ring dryer include:

• Excessive vibration or movement of the drum during operation 
• Noise or banging sounds from loose components   
• Deformation or cracking of the retaining ring itself
• The dryer door not closing properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This idler pulley shaft serves as the axle the idler pulley rides on, helping maintain proper belt alignment and tension. Replacing a worn shaft can reduce squealing, wobble, and belt wear so the drive system runs smoothly. What it does:

• Acts as the pivot/axle for the idler pulley within the belt-tensioner assembly
• Helps keep the drive belt aligned and properly tensioned
• Wear or scoring can cause pulley wobble, squeaking/squealing, or belt fraying
• Can contribute to belt slippage and intermittent loss of drive

• One idler pulley shaft

• Disconnect power; shut off gas or water supply if applicable
• Relieve belt tension and access the idler assembly
• Note and transfer any spacers, washers, or retainers from the old shaft to the new one
• After reassembly, the pulley spins freely on the shaft and the belt tracks correctly

The Dryer Blower Wheel is an OEM part for Whirlpool dryers. It is responsible for circulating air through the dryer drum and out the exhaust vent, ensuring efficient drying of clothes by maintaining proper airflow.

Causes of a bad blower wheel can include lint buildup, wear and tear over time, or damage from foreign objects that may have entered the dryer.

Symptoms of a bad blower wheel include:

• Reduced drying efficiency
• Unusual noises such as rattling or thumping during operation
• Overheating of the dryer
• Clothes taking longer than usual to dry

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.