Frigidaire Washer Dryer Combo FLEB8200FS2 Noisy

The Dryer Drum Bearing is an OEM part for Frigidaire dryers. It supports the dryer drum, ensuring smooth rotation during the drying cycle. This part attaches to the inside of the rear panel of the cabinet, offering support to the dryer drum. 

You should replace the drum bearing if it becomes worn out or damaged. Causes of a bad drum bearing can include normal wear and tear, overloading the dryer, or lack of lubrication.

Symptoms of a bad drum bearing include:

• Loud squeaking or grinding noises during operation
• The drum not turning smoothly or becoming misaligned
• Increased friction causing overheating or burning smells
• The dryer not tumbling clothes properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drum Glide is an OEM part for Frigidaire dryers. It is designed to support the front of the dryer drum as it rotates, allowing the drum to turn smoothly with minimal friction and noise. This is a single glide. Your dryer uses two so it is recommended to replace both at the same time.

Causes of a bad drum glide can include wear and tear from regular use, excessive loads that put undue strain on the drum and its components, or accumulation of lint and debris that can interfere with the glide's movement.

Symptoms of a bad Drum Glide can include:

• Unusual noises, such as screeching or squealing, during operation
• Increased difficulty in turning the drum, leading to longer drying times or incomplete cycles
• Visible wear or damage to the glide itself, indicating it is time for a replacement

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Lower Felt Seal is an OEM part for Frigidaire dryers. This part creates a tight seal between the drum and the front panel, preventing air leakage and reducing energy consumption.

Symptoms of a failing Lower Felt Seal include:

• Clothes getting snagged or caught during the drying cycle
• Increased drying times due to heat escaping from the drum
• Excessive noise or squeaking as the drum rotates
• Visible wear, tears, or gaps in the felt seal

Causes of a bad lower felt seal can include regular wear and tear from the constant rotation of the drum, physical damage from overloading the dryer, or deterioration due to exposure to heat and humidity over time.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Rear Drum Support Shaft is an OEM part for Frigidaire dryers, specifically designed to ensure the stability and smooth rotation of the dryer drum. This component plays a pivotal role in the dryer's operation by supporting the rear of the drum, allowing it to turn evenly and quietly during cycles. Note: The rear drum bearing kit is 5303281153.

The causes behind these issues often stem from normal wear and tear, excessive loads that strain the dryer's components, or lack of regular maintenance. Over time, the support shaft can wear down, become loose, or even corrode, leading to operational inefficiencies and potential damage to the dryer.

Symptoms of a failing Rear Drum Support Shaft include:

• Unusual noises, such as thumping or squeaking, during operation
• The dryer drum struggling to rotate or not rotating at all
• Increased wear on other components, such as the belt or motor, due to improper drum alignment

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Washer Drive Belt is an OEM part for Frigidaire washing machines. This belt connects the motor to the drum, enabling the drum to rotate during the wash and spin cycles. It ensures the proper transfer of power from the motor to the drum, allowing the washer to agitate and spin effectively.

Common causes of a bad drive belt include normal wear and tear, overloading the washer, or a misaligned drum that puts extra strain on the belt.

Symptoms of a bad washer drive belt include:

• The washer drum not spinning or agitating
• A burning smell during operation
• Unusual noises such as squealing or grinding
• The washer stopping mid-cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Upper Felt Seal is an OEM part for Frigidaire dryers. It provides a seal between the dryer drum and the front panel, helping to retain heat and ensure efficient drying performance. This felt seal also minimizes friction between the drum and the front panel, reducing wear on the drum and the appliance itself. The seal measures approximately 16.5" long x 1" wide. The adhesive is included as well.

Causes of a bad upper felt seal can include wear and tear over time, exposure to high heat, or damage from foreign objects caught in the drum. A compromised felt seal can lead to inefficient drying and increased energy consumption.

Symptoms of a bad upper felt seal include:

• Clothes taking longer to dry
• Excessive lint accumulation inside the dryer
• Unusual noises during the drying cycle
• Visible damage or gaps in the felt seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Also available in maintenance kit: Part Number 5304457724.

The Drum Belt is an OEM part for Frigidaire dryers. It plays a pivotal role in the mechanism of the dryer, connecting the motor to the drum to enable its rotation. Without a functioning belt, the dryer's drum will not turn, preventing clothes from drying properly.

Symptoms of a failing Drum Belt include:

• A dryer that turns on but does not spin
• Unusual noises, such as thumping or squealing, coming from the dryer
• Clothes taking longer than usual to dry
• The dryer stopping unexpectedly during a cycle

Common causes for Drum Belt issues are general wear and tear from regular use, the belt becoming stretched or misaligned, and excessive load sizes that strain the belt beyond its capacity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Blower Wheel is an OEM part for Frigidaire clothes dryers. This component works to propel hot air through clothes during drying cycles.

Causes of a bad blower wheel involve wear from years of operation, such as bearing deterioration or plastic fan blade cracking/warping. Foreign object damage or improper cleaning techniques pose other risk factors.

Symptoms of a bad blower wheel include:

• Slow or weak drying even on high heat settings
• Loud clanking or grinding noises from inside the duct
• The dryer not activating or functioning when turned on
• Reduced air discharge observable at the vent

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

The Frigidaire Drain Pump is an OEM part for Frigidaire washing machines. It plays a crucial role in the washer's operation by removing water from the wash tub at the end of each cycle, ensuring your clothes are properly drained before the spin cycle. 

Causes of a bad drain pump can include blockages from debris such as coins, lint, or small items that escape from clothing, as well as motor or impeller damage. Electrical failures can also impair pump function, leading to inadequate water removal.

Symptoms of a bad Frigidaire Drain Pump include:

• Water not draining completely from the washer
• Unusual noises, like humming or buzzing, indicating the pump is struggling
• Washer stopping mid-cycle
• Water pooling around the base of the machine

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Idler Pulley is an OEM part for Frigidaire dryers. It helps guide and maintain tension on the dryer drum belt, ensuring the drum rotates smoothly during the drying cycle.

Over time, the idler pulley can wear out due to friction and regular use, or it may become damaged from excessive strain or misalignment. If the idler pulley fails, the dryer drum may not rotate properly, leading to inefficient drying or a complete inability to dry clothes.

Symptoms of a bad Idler Pulley include:

• Squeaking or squealing noises during operation
• The drum not rotating or rotating unevenly
• The belt appearing loose or slipping off the drum

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Spin Bearing is an OEM part for Frigidaire washing machines, specifically designed to facilitate the smooth and efficient rotation of the washer drum. This bearing plays a pivotal role in the operation of your washing machine, allowing the drum to spin freely with minimal friction and noise.  

Causes for replacement may include wear and tear from regular use, water damage leading to rust or corrosion, or physical damage from excessive load sizes. 

Symptoms of a bad Spin Bearing include:

• Loud noises during the spin cycle, often described as grinding or rumbling
• The drum struggling to spin or not spinning as smoothly as it should
• A noticeable decrease in washing performance due to the drum's impaired movement

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

The Spin Bearing Washer is an OEM part for Frigidaire washing machines. Situated inside the transmission housing, this thin metal washer acts as a subsurface support for the belt pulley bearing. The spin-bearing washer facilitates smooth, balanced rotation essential for agitated and spun wash cycles.

Causes of a bad spin-bearing washer include wear and fatigue from years of successive rotations, potentially allowing excessive movement between housing components.

Symptoms of a bad spin-bearing washer involve:

• Vibration or shaking noises coming from inside the washer cabinet
• Belt slippage wasting energy by inefficiently spinning loads
• Increased friction resulting in longer cycle times for spins
• Failure of belts or other components from unsupported bearing

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement