Frigidaire Washer Dryer Combo FLSG72GCSD Leaking

The Tub Seal is an OEM part for Frigidaire washing machines. It is designed to create a water-tight seal between the washing machine tub and the transmission or drive system. This seal prevents water from leaking out during the operation of the washer and protects the mechanical components from water damage.

Symptoms of a failing tub seal include:

• Water leaking from the underside of the washing machine.
• Increased moisture or puddles forming under the machine during use.
• A musty or moldy smell, indicating that water has been seeping and not properly drying.

Causes of a bad tub seal can include aging and wear over time, exposure to harsh detergents that degrade the material of the seal, or mechanical stress from unbalanced loads that can cause the seal to fail. It's important to address these issues promptly to prevent further damage to the washing machine.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Inlet Valve Assembly is an OEM part for Frigidaire washing machines. This assembly controls the flow of water into the washing machine during the fill cycles, ensuring the correct amount of water enters the tub.

Over time, the water inlet valve can become faulty due to mineral buildup, wear and tear from frequent use, or damage to the valve components. If the valve is not functioning properly, it can result in issues with the water flow into your washing machine.

Symptoms of a bad water inlet valve assembly include:

• No water entering the washing machine
• The washer filling slowly or not at all
• The washing machine filling with water when it is turned off
• Leaks from the valve area

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drain Hose is an OEM part for Frigidaire washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle.

You should replace the drain hose if it becomes damaged or clogged. Causes of a bad drain hose include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Frigidaire Drain Pump is an OEM part for Frigidaire washing machines. It plays a crucial role in the washer's operation by removing water from the wash tub at the end of each cycle, ensuring your clothes are properly drained before the spin cycle. 

Causes of a bad drain pump can include blockages from debris such as coins, lint, or small items that escape from clothing, as well as motor or impeller damage. Electrical failures can also impair pump function, leading to inadequate water removal.

Symptoms of a bad Frigidaire Drain Pump include:

• Water not draining completely from the washer
• Unusual noises, like humming or buzzing, indicating the pump is struggling
• Washer stopping mid-cycle
• Water pooling around the base of the machine

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks

The Spin Bearing Washer is an OEM part for Frigidaire washing machines. Situated inside the transmission housing, this thin metal washer acts as a subsurface support for the belt pulley bearing. The spin-bearing washer facilitates smooth, balanced rotation essential for agitated and spun wash cycles.

Causes of a bad spin-bearing washer include wear and fatigue from years of successive rotations, potentially allowing excessive movement between housing components.

Symptoms of a bad spin-bearing washer involve:

• Vibration or shaking noises coming from inside the washer cabinet
• Belt slippage wasting energy by inefficiently spinning loads
• Increased friction resulting in longer cycle times for spins
• Failure of belts or other components from unsupported bearing

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.

The Spin Bearing is an OEM part for Frigidaire washing machines, specifically designed to facilitate the smooth and efficient rotation of the washer drum. This bearing plays a pivotal role in the operation of your washing machine, allowing the drum to spin freely with minimal friction and noise.  

Causes for replacement may include wear and tear from regular use, water damage leading to rust or corrosion, or physical damage from excessive load sizes. 

Symptoms of a bad Spin Bearing include:

• Loud noises during the spin cycle, often described as grinding or rumbling
• The drum struggling to spin or not spinning as smoothly as it should
• A noticeable decrease in washing performance due to the drum's impaired movement

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:

• Secures and centers the spin basket on the drive shaft for balanced rotation
• Transfers drive torque to the inner tub during spin
• Helps maintain basket alignment to reduce vibration
• Typical symptoms of failure: loose/wobbly tub, scraping or grinding noises, poor or no spin, frequent out-of-balance events

• 1 trunnion

• Disconnect power and water before service; wear gloves and eye protection
• Access the hub by removing top/access parts, then the agitator/wash plate and inner-tub fasteners
• Clean the shaft and mating surfaces; seat the new trunnion fully and tighten fasteners evenly in a crisscross pattern
• Inspect related parts (tub seal, bolts, bearing) while open and replace if worn; run a short test cycle to ensure smooth spin

Includes ATC