General Electric Dishwasher GHDA960K00BB Leaking

The Water Inlet Valve is an OEM part for GE dishwashers. It is responsible for opening and closing the water supply to the dishwasher. It regulates the water pressure and ensures the proper amount of water is dispensed for each cycle. This part has a 3/8” inlet and includes the mounting bracket.

Causes of a faulty water inlet valve can include wear and tear over time, sediment or debris buildup, electrical component failure, or damage due to high water pressure. These factors can result in issues such as inadequate water flow, leaks, or the dishwasher not filling or draining properly.

Symptoms of a bad water inlet valve may include:

• Insufficient water supply or low water pressure
• Leaks around the valve area
• Inability to start or complete dishwasher cycles

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Lower Door Gasket is an OEM part for GE dishwashers. This gasket is for creating a tight seal around the dishwasher door to prevent water from leaking out during cycles. 

Symptoms of a bad Lower Door Gasket include:

• Visible cracks or wear on the gasket.
• Water leakage around the dishwasher door.
• Frequent puddles forming under the door during operation.
• Dampness along the edges of the door after a wash cycle.

Causes of a bad door gasket can include regular wear and tear from use, improper door alignment, excessive cleaning chemicals that degrade the material, or thermal damage from high-temperature cycles. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Tub Gasket is an OEM part for GE dishwashers. This gasket provides a watertight seal between the dishwasher tub and the door, preventing water from leaking out during the wash and rinse cycles. 

Symptoms of a failing Tub Gasket include:

• Water leaking from the bottom or sides of the dishwasher door
• Visible wear, cracks, or tears in the gasket material
• The door not closing properly or feeling loose
• Increased moisture or water damage around the dishwasher area

Causes of a bad tub gasket can include wear and tear from regular use, exposure to high temperatures and detergents that degrade the material, or physical damage from improperly loading or unloading the dishwasher.

This OEM GE part is also compatible with some models from Hotpoint, RCA, and Kenmore models.

The Pump Connector is an OEM part for GE dishwashers. This connector joins the dishwasher’s pump to the drain hose, facilitating the proper expulsion of water during the draining cycle. It ensures a secure and leak-free connection, essential for the efficient operation of the dishwasher.

Over time, the pump connector can become compromised due to wear and tear, exposure to detergents and hot water, or damage from debris. If the connector fails, it can lead to leaks and drainage issues, impacting the dishwasher's performance.

Symptoms of a bad pump connector include:

• Water leaking from the bottom of the dishwasher
• Slow or incomplete drainage
• Puddles of water around the dishwasher
• Error codes related to drainage problems

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This kit is used to repair a leaking pump on GE made dishwashers. For a complete pump/motor assembly get WD26X10013.

The Sump is an OEM replacement part specific to GE-brand dishwashers. Located at the bottom of the wash chamber, the sump collects dirty water from each wash cycle.  

Causes of a bad sump can include cracks that leak water or mineral buildup clogging drain components over extended use. Improper drainage prevents the machine from functioning as designed.

Symptoms of an issue with the sump include: 

• Puddles or water leaks inside or outside the dishwasher 
• Standing water not fully draining after each cycle
• Moisture damage risking other internal parts

This part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drain Hose is an OEM part for GE dishwashers. This part carries the wastewater from the dishwasher to the household plumbing, ensuring efficient and effective drainage after each wash cycle.

Causes of a bad drain hose can include regular wear and tear, kinks or bends that restrict water flow, or damage from improper installation.  

Symptoms of a bad drain hose include:

• Water not draining properly from the dishwasher
• Leaks or puddles of water around the dishwasher
• Visible cracks or splits in the hose
• Unpleasant odors due to stagnant water

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This fill funnel directs the incoming water into the dishwasher and helps contain the flow to prevent splashing and leaks. Replacing a cracked or worn funnel restores a proper, sealed water path during the fill. What it does:

• Channels incoming water into the dishwasher during the fill
• Helps seal the opening to reduce splashing and external leaks
• Common symptoms include water leaking during fill, moisture around the inlet area, or visible cracks/deformation of the funnel

• 1 fill funnel

• Disconnect power and shut off the water supply before servicing
• Access the funnel at the water entry point for your model
• Remove the old funnel; seat the new funnel evenly and ensure the seal is fully seated
• Reassemble and run a quick fill to check for leaks

The Detergent and Rinse Aid Dispenser is an OEM part for GE dishwashers. It is responsible for holding and releasing detergent and rinse aid during the dishwashing cycle, ensuring that dishes are cleaned and rinsed effectively.

Causes of a bad detergent and rinse aid dispenser can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process. These issues can arise from regular use, buildup of detergent residue, or accidental impact.

Symptoms of a bad detergent and rinse aid dispenser include:

• Improper dispensing of detergent or rinse aid
• Insufficient cleaning or rinsing results
• Leaks or drips from the dispenser area
• The dispenser door not opening or closing correctly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected. 

Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure. 

Symptoms of a bad flood switch assembly include:

• The dishwasher not filling with water properly
• The dishwasher overfilling or leaking
• Error codes related to water levels
• The dishwasher not starting or stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher hose clamp secures a hose to its fitting to help prevent leaks. Replace a corroded or loose clamp to restore a tight, reliable seal at a hose connection point. What it does:

• Tightens around a dishwasher hose and fitting to maintain a watertight seal
• Helps resolve leaks at hose joints or beneath the unit
• Replaces clamps that are corroded, bent, stripped, or won't hold tension
• Symptoms include moisture at the connection, hose slipping off, or recurring leaks

• Includes 1 hose clamp

• Disconnect power at the breaker and shut off the water supply before servicing
• Access the affected hose connection and place a towel or pan to catch residual water
• Release and remove the old clamp; fully seat the hose, position the new clamp just behind the fitting's barb, and tighten/secure
• Run a short cycle and check for leaks at the connection