General Electric Dishwasher GLC5604V00BB Leaking

The Tub Gasket is an OEM part for GE dishwashers. This gasket provides a watertight seal between the dishwasher tub and the door, preventing water from leaking out during the wash and rinse cycles. 

Symptoms of a failing Tub Gasket include:

• Water leaking from the bottom or sides of the dishwasher door
• Visible wear, cracks, or tears in the gasket material
• The door not closing properly or feeling loose
• Increased moisture or water damage around the dishwasher area

Causes of a bad tub gasket can include wear and tear from regular use, exposure to high temperatures and detergents that degrade the material, or physical damage from improperly loading or unloading the dishwasher.

This OEM GE part is also compatible with some models from Hotpoint, RCA, and Kenmore models.

The Water Inlet Valve is an OEM part for GE dishwashers. This component controls the flow of water into the dishwasher, functioning to ensure the right amount of water is supplied during each wash cycle. The valve operates via electronic controls from the dishwasher, responding to the needs of various cycles and adjustments in water pressure.

Symptoms of a bad Water Inlet Valve include:

• Dishwasher not filling with water
• Water leaking from underneath the dishwasher
• Unusual noises, such as humming or buzzing, coming from the valve area

Causes of a bad water inlet valve can include sediment build-up which can obstruct the flow or prevent the valve from closing, wear and tear over time leading to leaks, or electrical failures that affect the valve’s operation.

This replacement part is also compatible with certain models of Hotpoint, RCA, and Kenmore dishwashers, enhancing its versatility and utility in home appliance repair.

The Pump Connector is an OEM part for GE dishwashers. This connector joins the dishwasher’s pump to the drain hose, facilitating the proper expulsion of water during the draining cycle. It ensures a secure and leak-free connection, essential for the efficient operation of the dishwasher.

Over time, the pump connector can become compromised due to wear and tear, exposure to detergents and hot water, or damage from debris. If the connector fails, it can lead to leaks and drainage issues, impacting the dishwasher's performance.

Symptoms of a bad pump connector include:

• Water leaking from the bottom of the dishwasher
• Slow or incomplete drainage
• Puddles of water around the dishwasher
• Error codes related to drainage problems

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Sump is an OEM replacement part specific to GE-brand dishwashers. Located at the bottom of the wash chamber, the sump collects dirty water from each wash cycle.  

Causes of a bad sump can include cracks that leak water or mineral buildup clogging drain components over extended use. Improper drainage prevents the machine from functioning as designed.

Symptoms of an issue with the sump include: 

• Puddles or water leaks inside or outside the dishwasher 
• Standing water not fully draining after each cycle
• Moisture damage risking other internal parts

This part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lower Door Seal is an OEM replacement part for GE dishwashers. Located along the bottom edge of the dishwasher door, this rubber seal creates an airtight barrier when closed to prevent leaks during wash cycles.

Causes of a faulty lower door seal often involve normal deterioration of rubber over extended use, allowing cracks to form and reducing its flexibility.

Symptoms of an inadequate lower door seal include:

• Puddles or water leaks beneath the appliance
• Mineral deposits left behind after drying cycles
• Inability to maintain optimal interior humidity
• Gaps appearing along the bottom door perimeter

This OEM GE replacement seal is also compatible with Hotpoint, RCA, and some Kenmore models.

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

The Circulation Pump Impeller Kit is an OEM replacement part for GE dishwashers. This kit includes the necessary impeller components responsible for circulating water throughout dishwashing cycles. 

Causes of a bad circulation pump assembly include normal wear from continuous pump operation, along with mineral or debris buildup that can affect water flow.

Symptoms include:

• Inadequate or lack of water circulation within cycles
• Dirty dishes even after full cycles due to insufficient cleaning 

This OEM GE part is compatible with some Hotpoint, RCA, and select Kenmore models. 

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This fill funnel directs the incoming water into the dishwasher and helps contain the flow to prevent splashing and leaks. Replacing a cracked or worn funnel restores a proper, sealed water path during the fill. What it does:

• Channels incoming water into the dishwasher during the fill
• Helps seal the opening to reduce splashing and external leaks
• Common symptoms include water leaking during fill, moisture around the inlet area, or visible cracks/deformation of the funnel

• 1 fill funnel

• Disconnect power and shut off the water supply before servicing
• Access the funnel at the water entry point for your model
• Remove the old funnel; seat the new funnel evenly and ensure the seal is fully seated
• Reassemble and run a quick fill to check for leaks

The Detergent and Rinse Aid Dispenser is an OEM part for GE dishwashers. It is responsible for holding and releasing detergent and rinse aid during the dishwashing cycle, ensuring that dishes are cleaned and rinsed effectively.

Causes of a bad detergent and rinse aid dispenser can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process. These issues can arise from regular use, buildup of detergent residue, or accidental impact.

Symptoms of a bad detergent and rinse aid dispenser include:

• Improper dispensing of detergent or rinse aid
• Insufficient cleaning or rinsing results
• Leaks or drips from the dispenser area
• The dispenser door not opening or closing correctly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected. 

Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure. 

Symptoms of a bad flood switch assembly include:

• The dishwasher not filling with water properly
• The dishwasher overfilling or leaking
• Error codes related to water levels
• The dishwasher not starting or stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher hose clamp secures a hose to its fitting to help prevent leaks. Replace a corroded or loose clamp to restore a tight, reliable seal at a hose connection point. What it does:

• Tightens around a dishwasher hose and fitting to maintain a watertight seal
• Helps resolve leaks at hose joints or beneath the unit
• Replaces clamps that are corroded, bent, stripped, or won't hold tension
• Symptoms include moisture at the connection, hose slipping off, or recurring leaks

• Includes 1 hose clamp

• Disconnect power at the breaker and shut off the water supply before servicing
• Access the affected hose connection and place a towel or pan to catch residual water
• Release and remove the old clamp; fully seat the hose, position the new clamp just behind the fitting's barb, and tighten/secure
• Run a short cycle and check for leaks at the connection