Maytag Dryer MDG16CSAEW Will not tumble or doesn't tumble

The Dryer Drum Belt is an OEM replacement part for Whirlpool electric dryers. This belt rotates the tumbling drum to fluff and dry clothing loads efficiently. Continuous, uninterrupted drum movement is necessary for effective drying performance. This high-quality belt features 4 grooves and 5 ribs, with a width of 5/16" and a length of 91 5/8".

Causes of a faulty belt include breakage from age, cracks developing as rubber dries out, or slipping off the pulleys due to looseness or worn grooves.

Symptoms of a bad dryer belt include:

• Drum fails to turn or rotates slowly during cycles
• Loud squealing, screeching noises originating from inside  
• Smoky smells from belt slipping against fast-turning pulleys
• Possible jolts, jerks or prevented operation of dryer 

This belt is also compatible with KitchenAid, Maytag and Jenn-Air models too.

The Belt Tension Pulley is an OEM part for Whirlpool dryers. It is crucial for maintaining the correct tension on the dryer belt, ensuring that it runs smoothly and the drum turns properly during operation. This pulley helps to keep the belt aligned and prevents it from slipping, which is essential for the efficient performance of your dryer.

Symptoms of a bad Belt Tension Pulley include:

• Unusual noises, such as squeaking or grinding, coming from the dryer when it is running.
• The dryer drum failing to turn, even though the motor is running.
• Excessive wear or damage to the dryer belt.

Causes of a bad belt tension pulley can include wear and tear from regular use, accumulation of lint and debris which may impede the pulley’s movement, or a failing bearing within the pulley assembly.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drum Support Roller is an OEM replacement part for Whirlpool dryers that is responsible for supporting the drum and allowing it to rotate smoothly. Causes of a bad Drum Support Roller can include lint and debris that accumulates and causes the rollers to malfunction or seize.

Causes of bad Drum Support Rollers can include wear and tear over time, excessive load imbalances, or physical damage from impact or mishandling.

Symptoms of a bad Drum Support Roller include:

• Unusual noises, such as thumping or squealing.
• The dryer drum struggling to rotate or not turning smoothly.
• Increased vibration or shaking of the dryer during operation.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Idler Shaft Washer is an OEM part for Whirlpool dryers. This small but essential component fits on the idler pulley shaft, playing a crucial role in maintaining the alignment and tension of the dryer belt.

Symptoms of a bad Idler Shaft Washer include:

• Squeaking or squealing noises during operation, indicating misalignment or friction.
• The dryer drum failing to turn smoothly or at all.
• Excessive wear or damage to the dryer belt.
• Unusual vibrations during dryer operation.

Causes of a bad idler shaft washer can include wear and tear from regular use, loss of material integrity leading to thinning or breaking, or improper installation that may cause misalignment and increased friction.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dryer Drive Motor is an OEM replacement part for Whirlpool dryers. It is a crucial component that provides the necessary power and rotational force to turn the dryer drum during the drying cycle.

Symptoms of a faulty dryer drive motor include:

• The dryer drum not rotating or rotating slowly
• Loud grinding or squeaking noises during operation
• Overheating or burning smell from the motor area

Causes of a bad dryer drive motor can include normal wear and tear over time, bearing failure, electrical malfunctions, or physical damage from foreign objects or debris.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models. 

The Idler Pulley Arm is an OEM replacement part for Whirlpool dryers. As a connecting part, it works to route the drive belt and suspend the idler pulley. Mounted on a pivoting bracket, the durable arm positions the idler pulley to maintain proper belt tension over the lifter roll and drum.

Causes of a bad idler pulley arm can include fatigue from extended use, damage from overtightened belts, or broken welds impairing motion.

Symptoms of a bad idler pulley arm include:

• Slipping or prematurely worn drive belts
• Reduced or inconsistent drum rotation
• Grating noises or abnormal vibrations during use

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

The Idler Shaft Retaining Ring is an OEM replacement part for Whirlpool dryers. Also called an "E" ring, it is a sealing gasket positioned between the front and rear housing omponents. Maintaining an airtight seal prevents gas leakage and promotes efficient drying performance.  

Causes of a bad retaining ring commonly involve compression loss of the rubber gasket material over many years of heating cycles. Exposure to petroleum-based cleaners may prematurely deteriorate the seal as well.

Symptoms of a failed 'E' ring include: 

• Gas leaks emitting foul odors around seams or vents   
• Reduced heat conductivity hampering dryer functioning
• Moisture accumulation shortens fabric lifespan  
•  Drafts compromising indoor air quality and energy bills

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models. 

The Retaining Clip is an OEM part for Whirlpool stand mixers. This small but essential part ensures the stability and secure fitting of various mixer components, contributing significantly to the appliance's overall performance and durability. Its primary role is to hold parts in place, preventing movement that could lead to wear or malfunction during operation.

Stand mixers are subjected to a variety of stresses, particularly when mixing thick doughs or other dense mixtures. The retaining clip's integrity is vital in these situations, as it helps to maintain the correct alignment and functioning of the mixer's moving parts. 

Symptoms of a bad Retaining Clip in a stand mixer include:

• Components such as beaters or attachments becoming loose or detaching during use.
• Unusual vibration or noise 
• Difficulty in attaching or detaching mixer attachments  

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Door Switch Kit is an OEM part for Whirlpool dryers. This kit includes a door switch that plays a crucial safety and operational role in the dryer's function. It ensures that the dryer operates only when the door is firmly closed, preventing the machine from running with an open door, which could pose safety risks and inefficiency in the drying process.

The causes of door switch failure often include physical damage from slamming the dryer door, wear and tear over time, or electrical issues such as short circuits. 

Symptoms of a faulty Dryer Door Switch include:

• The dryer not starting when the door is closed 
• The dryer continuing to run when the door is opened, which poses a significant safety hazard.
• Unusual noises from the switch area 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This idler spring maintains proper tension on the dryer's drive belt by pulling the idler arm. Replacing a weak or broken spring restores consistent drum rotation and helps prevent belt slippage and noise.

• Applies tension to the idler pulley arm to keep the drive belt tight
• Helps the motor turn the drum smoothly without belt slip
• A worn, stretched, or broken spring may cause the drum not to turn or the belt to slip off
• Can contribute to squealing or chirping from the belt/pulley area

• Disconnect power; turn off gas supply for gas dryers
• Access the belt path; note belt routing and spring attachment points before removal
• Release belt tension, move the idler arm, attach the new spring, and re-tension the belt
• Rotate the drum by hand to verify belt tracking before reassembly and test run