Maytag Refrigerator MSD2356AEB Fridge too warm

Adaptive defrost control board.

This evaporator fan motor circulates cold air across the evaporator coils and through the freezer and fresh-food sections to maintain even temperatures. Replacing a failed or noisy motor restores proper airflow and dependable cooling performance.

• Drives the evaporator fan blade to move air over the coils and throughout the cabinet
• Helps maintain consistent temperatures between freezer and refrigerator compartments
• Failure symptoms include weak/no airflow, the fan not running, loud squealing/rumbling, or the fresh-food section warming up
• Poor airflow can also lead to frost or ice buildup on the freezer back panel

• Disconnect power before servicing; wear cut-resistant gloves and eye protection
• Access the motor behind the freezer's rear panel; use caution around sharp metal and evaporator fins
• Note wire positions; transfer the fan blade and any brackets/grommets from the original motor; secure wiring connections
• Ensure the blade spins freely; engage the door switch when testing and strong airflow after reassembly

This assembly contains the evaporator defrost heater and temperature thermostat that remove frost from the evaporator coil to help restore normal cooling. Replaces failed defrost components to help the fridge complete defrost cycles and reduce ice buildup. What it does:

• Heats the evaporator during defrost cycles so accumulated frost melts away
• Uses a temperature thermostat to open/close the heater circuit at the correct temperature
• Commonly replaces failed defrost parts when frost builds on the evaporator or the refrigerator runs continuously
• Helps restore normal airflow and cooling when defrost cycle has stopped functioning

• One defrost heater and thermostat assembly

• Disconnect power to the appliance before starting any repair
• Handle the evaporator and fins carefully to avoid damage; keep electrical connections secure and dry
• Follow the manufacturer instructions for routing and mounting the assembly

Hinge pin with door cam.

This refrigerator door closer restores smooth, positive door action. When worn, the door can click, bind, or swing open. Replacing it helps the door seal properly to maintain temperatures and limit frost or moisture.

• Provides cam action at the bottom hinge for smooth opening and a positive close
• Helps pull the door shut during the last inches of travel to maintain gasket contact
• Typical wear symptoms: popping/clicking at the lower hinge, door that won't stay closed, or poor sealing
• Visual clues include flat spots, grooves, or cracks on the cam surface

• Disconnect power and remove items from the door for safety and to reduce weight
• Lift the door off the bottom hinge; transfer/install the closer in the same orientation as the original
• Reassemble, then verify the door self-closes and the gasket seals evenly
• Use care not to pinch or distort the door gasket during reinstallation

This defrost heater clip secures the refrigerator's defrost heater to the evaporator assembly, keeping the heater in proper position for reliable defrost cycles and helping prevent ice buildup that impairs cooling performance. What it does:

• Secures the defrost heater to the evaporator so the heater maintains proper contact and alignment.
• Helps ensure the heater can melt frost and ice during automatic defrost cycles.
• Small replacement part that restores proper heater placement without replacing the entire assembly.

• Disconnect power to the appliance before accessing the evaporator or heater to avoid shock or injury.
• Replacement typically requires removing interior panels or an evaporator cover; handle evaporator fins carefully—they are sharp.
• Verify the heater and wiring are undamaged and positioned correctly when installing the clip.

This thermal overload protector helps prevent motor overheating by interrupting power when temperatures exceed safe limits. It restores normal operation once the motor cools, protecting the appliance from damage and reducing risk of failure. What it does:

• Senses excessive motor temperature and interrupts current to stop the motor from running when overheated
• Helps prevent motor burnout and related electrical damage
• Can resolve symptoms such as a dryer or washer motor that stops mid-cycle, won't start, or trips the circuit during heavy use
• Works as a safety device in the motor circuit rather than a control or relay

• One thermal overload protector

• Disconnect power before accessing or replacing the motor overload; follow appliance-specific service manual steps
• Handle terminals and wiring carefully; replace using the same connections and orientation as the original
• If the motor repeatedly overheats after replacement, inspect motor bearings, venting, or other causes rather than replacing overload repeatedly