Maytag Washer MAH20PRDWW Leaking

Front load washer door boot seal, comes with drain plug and clamp.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Lip Seal Kit is an OEM replacement part for Whirlpool washing machines. It contains new seals that surround the tub opening and help prevent water leaks. This lip seal kit includes the revised lip seal, grease, O-ring, seal tool, washer kit, and instructions. The rear bearings are sold separately. Their part numbers are WP22003441 and WP22002934.

Symptoms of failed lip seals include:

• Water leaks from around the washer opening or tub area  
• Puddles or standing water underneath after a cycle
• Visible cracks or splits in existing seals

Causes may involve standard wear from machine operation, rubbing against the tub surface. Mineral buildup can also shorten seal lifespan if not periodically cleaned.

This OEM Whirlpool part fits models by Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washing machines. 

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This drain hose carries used water away from your appliance during the drain cycle. Replacing a worn or damaged hose helps stop leaks and restores proper draining performance.

• Routes wastewater from the appliance's drain system to the household drain
• Replaces hoses that are cracked, brittle, clogged, or kinked and leaking
• Can help when cycles end with standing water or slow/failed draining
• Helps reduce odors and backflow when installed and routed correctly

• Disconnect power and water supply; allow the appliance to cool before servicing
• Move the unit for access; keep towels or a pan handy to catch residual water
• Transfer and tighten existing clamps/fittings to the new hose; route without kinks and secure per your model's instructions
• Run a short test cycle and check all connections for leaks

The Drain Pump Assembly is an OEM part for Whirlpool washing machines. This part is responsible for removing water from the washer during the drain cycle. 

Causes of a bad drain pump assembly can include blockages from debris, wear and tear on the pump motor, or damage from objects accidentally left in pockets.  

Symptoms of a bad drain pump assembly include:

• The washer not draining water
• Water remaining in the tub after a cycle
• Unusual noises during the drain cycle
• Error codes related to draining issues

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This door boot drain hose channels residual water from the lower edge of the washer's door boot back into the tub/drain path. Replacing a cracked or clogged hose helps prevent front leaks, standing water, and musty odors around the gasket.

• Directs water away from the door boot/gasket into the tub or drain circuit
• Common symptoms: water pooling in the boot, leak at the front base, or musty odor near the door
• Replace if the hose is cracked, brittle, kinked, blocked, or leaking
• Restores proper draining from the door seal area

• Disconnect power and turn off water supply before servicing
• Access the hose at the door boot and its mating port; place towels to catch residual water
• Transfer or replace clamps as needed; fully seat hose on fittings and orient clamps correctly
• Run a short test cycle and check for leaks

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This tub cover seal is a molded rubber gasket that helps keep wash water inside the tub and seals the cover area to prevent leaks. It restores a watertight seal and reduces seepage and debris buildup around the tub cover. What it does

• Seals the joint between the tub and tub cover to help prevent water leaks during cycles
• Cushions the cover edge to reduce noise and vibration
• Helps block lint, detergent residue and moisture from entering gaps
• Common symptoms: visible water on the floor near the tub cover, persistent dampness, or visible wear/cracking of the existing seal

• Disconnect power and water before beginning any repair
• Verify correct orientation and full seating of the gasket around the tub cover; replace if torn, deformed, or hardened
• Removal/installation may require access to the control panel or outer cabinet depending on model

This grommet seals and cushions the dryer/refrigerator vent tube where it passes through the cabinet, helping prevent air leaks and reduce vibration noise. It restores a tight vent connection for proper airflow and quieter operation. What it does

• Provides a secure, flexible seal around the vent tube to reduce air leaks.
• Cushions the vent tube to minimize vibration and rattling during operation.
• Helps maintain proper airflow by keeping the vent connection aligned.
• Commonly replaced when cracked, torn, or excessively worn.

• One vent tube grommet.

• Turn off and unplug the appliance (or disconnect power) before starting any repair.
• Access may require removing the back panel or interior trim—follow your model's service instructions.
• Inspect surrounding vent tubing and fasteners; replace any damaged components for a complete repair.