Maytag Washer SAV515DEWW Leaking

This washer drain hose channels used water from the pump to your home drain. A sound, properly routed hose helps prevent leaks and backups during the drain cycle for reliable performance and a cleaner laundry area.

• Routes wastewater from the drain pump to the standpipe or laundry tub
• Replaces hoses that are cracked, brittle, split, kinked, or leaking
• Common fix for leaks at the back of the washer or slow/failed draining
• Restores a secure, watertight path when correctly clamped and routed

• Disconnect power and turn off water; expect some residual water—use towels or a pan
• Wear gloves; edges and clamps can be sharp
• Transfer and reuse existing clamps/brackets if your model uses them; ensure snug connections at both ends
• Route to the manufacturer-recommended height and secure to the standpipe; avoid kinks and test drain

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This tub-to-pump drain hose carries wash water from the washer tub to the drain pump so the machine can pump out during drain cycles. It replaces a cracked, split, or clogged hose to stop leaks and restore proper draining. What it does

• Directs tub water to the drain pump during drain and spin cycles
• Seals at tub and pump connections with hose clamps to prevent leaks
• Restores normal draining when original hose is damaged, cracked, or collapsed
• Helps prevent water on the floor and washer failure-to-drain symptoms

• Disconnect power and turn off water supply before starting any repair
• Remove lower access panel or cabinet to access hose and clamps
• Inspect and reuse or replace clamps as needed; secure hose ends evenly to avoid leaks
• Route hose without sharp bends or kinks; check for leaks after reconnecting power and running a short cycle

This replacement main bearing assembly supports the washer's drive/spin system. It keeps the inner basket and drive shaft rotating smoothly and quietly, helping maintain alignment and reducing vibration during wash and high-speed spin.

• Supports and centers the spin basket/drive shaft for low-friction rotation
• Helps reduce noise and vibration when spinning at high RPMs
• Restores smooth operation when the original bearing is worn or rough
• Common symptoms: roaring/grinding during spin, basket wobble/play, roughness turning by hand, possible leak at rear center if related seal wear is present

• Disconnect power and water before service; allow the appliance to cool
• Access and replacement procedures vary by model; significant disassembly is typical
• A bearing press/driver may be required; inspect shaft and related seals and replace if worn
• After reassembly, run a test spin to check for leaks