Maytag Washer SAV571EEWW Noisy

The Washer Idler Pulley Wheel is an OEM part for Whirlpool washing machines. This component is designed to maintain the appropriate tension on the washer's drive belt, ensuring smooth and efficient operation during the wash and spin cycles. It helps to reduce wear on the belt and other moving parts.

You should replace the idler pulley wheel if it becomes worn, damaged, or if the bearings fail. Common causes of a bad idler pulley wheel include regular wear and tear from continuous use, exposure to excessive loads, or debris causing damage to the wheel or bearings.

Symptoms of a bad idler pulley wheel include:

• Squeaking or grinding noises during operation
• The washer not spinning or agitating properly
• The drive belt slipping or coming off
• Increased vibration or shaking during cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement main bearing assembly supports the washer's drive/spin system. It keeps the inner basket and drive shaft rotating smoothly and quietly, helping maintain alignment and reducing vibration during wash and high-speed spin.

• Supports and centers the spin basket/drive shaft for low-friction rotation
• Helps reduce noise and vibration when spinning at high RPMs
• Restores smooth operation when the original bearing is worn or rough
• Common symptoms: roaring/grinding during spin, basket wobble/play, roughness turning by hand, possible leak at rear center if related seal wear is present

• Disconnect power and water before service; allow the appliance to cool
• Access and replacement procedures vary by model; significant disassembly is typical
• A bearing press/driver may be required; inspect shaft and related seals and replace if worn
• After reassembly, run a test spin to check for leaks

Can be upper or lower bearing depending on application.

This brake pad kit includes the replacement friction pads used to stop and hold the drum or internal assembly in place, restoring normal stopping performance and preventing excess drum rotation. Designed to match the original OEM fit and function. What it does:

• Replaces worn friction pads that allow the drum or assembly to stop properly
• Helps eliminate slow spin-down, slipping, or uncontrolled drum rotation
• Restores proper braking force for safe operation
• Reduces noise and wear caused by worn brake surfaces

• One brake pad kit

• Disconnect power before servicing to avoid shock or injury
• Inspect mating surfaces and related hardware; replace any damaged parts for reliable operation

The Drive Belt is an OEM replacement part for Whirlpool washing machines. This belt transmits power from the motor to turn the inner tub. Length: 28 3/4 inches. Washer spin and agitation belt

Causes of a bad drive belt can include cracks from repeated flexing cycles or damage from impacts over time. Operational vibrations may accelerate belt wear.

Symptoms of a bad drive belt include:

• Inner tub failing to rotate or turn very slowly  
• Grinding or squealing noises when running
• Long wash cycles as clothes lack adequate tumbling 

This OEM Whirlpool replacement is also compatible with Maytag, Amana, Jenn-Air, and some Kenmore front-load washer models as well. 

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

• Provides spring tension to clamp and retain a part, seal, or panel
• Helps maintain alignment and reduce vibration or rattling
• Restores secure attachment when the original clip is bent, stretched, or missing
• Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

• Disconnect power; turn off water supply if applicable
• Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
• Note the original orientation before removal to ensure proper reinstallation
• Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

This top load washer agitator assembly includes both the upper and lower parts of the agitator.