Whirlpool Dryer LER4634EQ2 Too hot

This Dryer Cycling Thermostat is an OEM replacement part for Whirlpool dryers. It monitors internal temperatures and cycles power to the heating element accordingly. The thermostat ensures the drying air reaches and maintains the optimal heat level selected for fast, effective drying results.

Symptoms of a bad cycling thermostat include:

• The dryer not heating or heating inconsistently  
• Frequent trips of the circuit breaker
• Slower than normal drying times
• Burned clothes due to overheating

Causes of failure may be related to normal wear over time, dust buildup affecting sensor readings, or incorrect thermostat calibration. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This dryer thermal cut-off kit is an authentic OEM replacement part for Whirlpool and Kenmore dryers. It is designed to prevent the dryer from overheating.

This Kit Includes:

• High Limit Thermostat (250°F Limit)
• A Cut Off Fuse (309°F Limit)
• Female Spade Terminals
• Jumper Wires

Over time, these components can fail due to electrical issues, lint buildup blocking the exhaust vent, or normal wear and tear. A malfunctioning thermal cut-off kit can result in overheating, which can pose a safety hazard and affect the dryer’s performance.

Symptoms of a bad Thermal Cut-Off Kit include:

• Dryer not heating
• Dryer overheating
• Dryer shutting off mid-cycle
• No response when attempting to start the dryer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hi-Limit Thermostat is an OEM part for Whirlpool dryers. It functions as a critical safety device that monitors and controls the temperature within the dryer, preventing it from overheating. When the dryer reaches a temperature that is too high, this thermostat will cut off the power to the heating element to mitigate the risk of fire.

Symptoms of a bad Hi-Limit Thermostat include:

• Dryer not heating adequately or at all
• Clothes taking longer than usual to dry
• The dryer repeatedly shutting off during a cycle
• Excessive heat emitted from the dryer even on lower settings

Causes of a bad Hi-Limit Thermostat can include a malfunction due to electrical issues, lint buildup causing restricted airflow and increased temperature, or failure of other components like the cycling thermostat that can cause the dryer to overheat.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Restore full heat and end long dry cycles - install the Whirlpool OEM Dryer Heating Element.

Why this heating element?

• Factory-spec 5400 W / 240 V heating element with nickel-chromium coil - built by Whirlpool to Whirlpool OEM standards.
• Broad compatibility: fits Whirlpool, Kenmore 110-series, Roper, Estate, Amana, Maytag & more 27-inch dryers.
• Built to last: high-temp terminals & mica insulation resist fatigue and hotspots.

Fixes these common dryer problems

DIY install — about 20 minutes

1. Unplug dryer and remove back panel to access heater housing.
2. Disconnect wires; remove housing screws and slide assembly out.
3. Swap old element for new, re-use hi-limit thermostat if still good.
4. Re-assemble, run test cycle - enjoy fast, even drying.

Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.

Why this belt?

• Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
• Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
• Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.

Fixes these common dryer problems

DIY install — about 15 minutes

1. Unplug dryer; remove lint screen housing & front panel.
2. Release belt tension at idler pulley; lift drum slightly to slide old belt off.
3. Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
4. Re-assemble, run test cycle - enjoy quiet, consistent tumbling.