630A Parts

This insulating part cushions and thermally isolates internal components to help reduce heat transfer and vibration noise in the appliance. It's a small replacement piece that restores proper spacing and protection around sensitive parts. What it does:

• Provides thermal separation between hot components and surrounding cabinet parts to help prevent heat damage
• Cushions components to reduce vibration and rattling noises during operation
• Helps maintain correct part clearances for safe, reliable performance
• Used where original insulation was damaged, missing, or deteriorated

• Disconnect power and, if applicable, water before beginning any repair
• Handle carefully; avoid compressing or tearing the insulation during installation
• Verify correct orientation and secure fit against the intended component or cabinet surface

This replacement cover protects internal components and finishes the appliance's exterior where installed. It restores a clean, secure appearance and helps prevent dust, moisture, and debris from reaching sensitive parts. What it does:

• Serves as a protective access panel for internal components
• Shields wiring, connectors, and electronics from dust and incidental contact
• Restores the appliance's exterior finish for a cosmetically complete repair
• Helps maintain safe operation by covering moving or live parts

• Before installing, disconnect power and water to the appliance to avoid shock or injury.
• Remove any trim or fasteners holding the old cover; keep screws for reuse.
• Align the cover carefully and secure with the original mounting hardware; do not force parts.
• If plastic clips or tabs are damaged, replace them to ensure a secure fit.

This replacement cup rack secures cups and small glassware on the dishwasher's upper rack, keeping items upright and preventing shifting during the wash for more consistent cleaning results. What it does:

• Provides dedicated support for cups, mugs and small glasses on the upper rack
• Helps prevent tipping, sliding and breakage during wash cycles
• Restores missing, cracked or warped cup-holding sections
• Compatible with dishwasher upper rack mounting points and clips

• One cup rack assembly

• Remove the upper rack for easier access; refer to your dishwasher manual for rack removal steps
• Align and snap the rack into the designated upper-rack mounting points; some models may use retaining clips or small fasteners
• Handle edges and clips carefully to avoid damage; wear gloves if needed

A narrow trim strip that finishes and protects an appliance panel edge, giving a clean look while covering gaps and edges. It helps keep dirt out of seams and improves the appliance's appearance. What it does:

• Covers exposed panel edges for a finished, seamless appearance
• Protects against dirt and debris entering narrow seams
• Helps prevent snagging on the panel edge during use
• Can reduce light or airflow through small gaps around the panel

• One trim strip

• Disconnect power to the appliance before performing any work
• Trim or align the strip carefully to avoid damaging the finish
• May attach with clips or adhesive; keep any original fasteners for re-use

This push-style control panel button restores tactile input for your appliance's front control assembly, letting you select cycles and settings again without replacing the entire panel. Commonly used where individual buttons snap into the console. What it does:

• Replaces a worn, broken, or missing push button on the control or console panel
• Restores responsive, tactile feedback for cycle and option selection
• Helps stop accidental presses caused by cracked or loose buttons
• Works with the existing switch beneath the panel when fitted correctly

• Power off and unplug the appliance before accessing the control panel
• Remove the console or trim per your model's service instructions to access the button retainer
• Snap the new button into the bezel until it seats; verify proper movement and switch actuation
• If the underlying switch or retainer is damaged, inspect and replace those parts as needed

This is a replacement electrical cable harness used to restore power or signal connections inside compatible appliances. It provides a direct, OEM-style connection for reliable operation and safer performance than damaged wiring. What it does:

• Replaces damaged or frayed wiring that can cause loss of power, intermittent operation, or control failures
• Restores proper electrical connections between components to prevent shorts or erratic behavior
• Helps eliminate issues like unresponsive controls, motors that won't run, or intermittent cycle problems
• Matches the OEM routing and connector style for correct fit and reliable contact

• Disconnect power before starting any repair to avoid shock or injury
• Inspect connectors and routing; replace any retainers or clips that are damaged
• Ensure connectors are fully seated and wires are routed away from moving parts and heat sources

This replacement charcoal filter restores odor control in recirculating range hoods by trapping cooking smells and airborne particles before air is returned to the kitchen. Use when odors persist despite normal cleaning. What it does:

• Adsorbs and reduces cooking odors in recirculating/ductless hood configurations
• Helps maintain fresher kitchen air when ducting to outdoors is not available
• Works alongside grease filters to improve overall ventilation performance
• Common sign it's needed: persistent or strong cooking smells after running the hood

• Turn off power to the hood before accessing filter area
• Remove and replace per your hood's instructions; typically installs behind the grease filter or in a dedicated cartridge slot
• Dispose of used charcoal filter according to local regulations

This moisture shield protects internal components from water and condensation, helping prevent moisture damage that can cause corrosion or electrical problems. Simple replacement maintains proper moisture control and appliance reliability. What it does:

• Redirects or blocks water and condensation away from sensitive parts
• Helps prevent shorting, corrosion, and moisture-related failures
• Supports normal drainage and airflow in the affected area
• Restores the appliance's original moisture-protection layout after damage or wear

• One moisture shield

• Replace with the appliance powered off and unplugged for safety
• Inspect mounting tabs and surrounding seals; replace any damaged fasteners
• Position the shield exactly as the original part to maintain drainage paths
• Address affected components before reassembly

This insulating part provides electrical and thermal isolation for internal appliance components, helping protect wiring and nearby parts from heat and shorting. It's a simple replacement used when the original is damaged or degraded. What it does:

• Separates and insulates electrical connections to reduce risk of shorts and arcing
• Helps block heat transfer from heaters or motors to nearby components
• Restores proper spacing and protection when the original insulator is cracked or worn
• Stops related symptoms like burning smell, intermittent electrical contact, or visible charring near wiring

• One insulating part

• Disconnect power (unplug appliance or switch off breaker) before starting any work
• Follow the appliance's service manual or wiring diagram for correct placement and orientation
• Replace only with the same part to maintain proper fit and insulation; do not modify the part
• If you see damaged wiring or connectors, inspect and repair those as well.

This holder is a small mounting bracket that secures internal components in place, helping prevent movement and noise while the appliance runs. It restores proper alignment and reduces loose or rattling parts. What it does:

• Secures control modules, hoses, or assemblies to the appliance frame
• Prevents vibration and movement that can cause noise or wear
• Helps maintain proper alignment of connected components
• Common symptom: loose or rattling parts near the holder location

• One holder/mounting bracket

• Disconnect power (and water if applicable) before starting any repair
• Inspect mating surfaces for damage; replace if worn or broken
• Use appropriate tools and fasteners; do not overtighten plastic tabs